Table of Contents
Advertisement
Sabbath mode
en
FSabbath mode
W ith the Sabbath mode, a cooking time of up to 74
S a b b a t h m o d e
hours can be set. You can keep the food in the cooking
compartment warm without having to switch the oven
on or off.
Starting Sabbath mode
Prerequisite: "Sabbath mode activated" is activated in
the basic settings. ~ "Basic settings" on page 15
The cooking compartment heats up with top/bottom
heating and a temperature between 85 °C and 140 °C.
Press the On/Off button.
1.
A type of heating and a temperature are suggested
in the display.
Turn the rotary selector anti-clockwise and select the
2.
"Sabbath mode" type of heating.
Touch the suggested temperature and set the
3.
temperature using the rotary selector.
Press the
button to open the time-setting options
0
4.
menu and touch the "Cooking time" field.
25:00 hours are suggested.
Use the rotary selector to set the required cooking
5.
time.
Press the Start/Stop button to start.
6.
You can see the cooking time counting down in the
status bar.
The cooking time has elapsed
A signal sounds. The oven stops heating. "Finished"
appears in the status bar.
Setting a later end time
It is not possible to set a later end time.
Cancelling Sabbath mode
Press the On/Off button. All settings are deleted. You
can apply new settings.
.Cleaning function
T he self-cleaning surfaces in the cooking compartment
C l e a n i n g f u n c t i o n
are cleaned when the operating mode is set to
"Cleaning function".
The self-cleaning surfaces (back panel, ceiling panel
and side panels) are coated with a porous, matt
ceramic material. This coating absorbs and breaks
down splashes from baking, roasting and grilling while
the oven is in operation. If the surfaces no longer clean
themselves adequately and dark patches appear, the
surfaces can be cleaned by the cleaning function.
The appliance records the number of times it is
Note:
used. The appliance indicates when it has reached a
point in time after which cleaning is recommended. The
recommendation is displayed until the cleaning function
has finished.
16
If you do not act on this recommendation, the self-
cleaning surfaces may become damaged.
If your appliance is already prematurely very dirty or if
you notice dark patches on the back panel, do not wait
until your appliance recommends cleaning to do so.
This is because the more often the appliance is
cleaned, the longer the self-cleaning surfaces will retain
their cleaning capability. You can clean your appliance
at any time as required using the cleaning function.
Before running the cleaning function
Remove shelves, rails, accessories and ovenware from
the cooking compartment.
Cleaning the cooking compartment floor and the
inside of the appliance door
Remove the worst dirt from the cooking compartment
floor, the inside of the appliance door and the interior
lighting. Otherwise, patches will appear that can no
longer be removed.
Caution!
Do not use oven cleaner on the self-cleaning surfaces.
This will damage the surfaces. If oven cleaner does get
onto these surfaces, dab it off immediately using water
and a sponge cloth. Do not rub the surface and do not
use abrasive cleaning aids. ~ "Cleaning" on page 18
:
Warning – Risk of burns!
The appliance becomes very hot on the outside
;
during the cleaning function. Never touch the appliance
door. Allow the appliance to cool down. Keep children
at a safe distance.
Setting the cleaning function
Cleaning lasts 60 minutes.
The duration cannot be changed.
Press the menu button.
1.
The operating modes menu opens.
Select the "Cleaning function" operating mode.
2.
If you touch the "Next" field, information on the
cleaning operation is displayed.
Press the "Start/stop" button to start the cleaning
3.
operation.
You can see the duration counting down in the
status bar.
Keep the kitchen ventilated while cleaning is in
progress.
Once the cleaning has finished
An audible signal sounds. The oven stops heating.
"Finished" appears in the status bar. Use the
to switch off the audible signal.
Cancelling cleaning
Press the On/Off button. All settings are deleted. You
can implement new settings.
Caution!
The cleaning recommendation is not reset. The
recommendation to run the cleaning function appears
on the display.
button
0
Advertisement
Table of Contents
