Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZDI 22001XA
Summary of Contents for Zanussi ZDI 22001XA
- Page 1 User Manual GETTING STARTED? EASY. ZDI 22001XA EN User Manual Dishwasher...
-
Page 2: Safety Information
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. CHILDREN AND VULNERABLE PEOPLE SAFETY This appliance can be used by children aged from 8 years and •... -
Page 3: Safety Instructions
Do not keep the appliance door open without supervision to • prevent to fall on it. Before maintenance, deactivate the appliance and disconnect • the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. •... - Page 4 DISPOSAL WARNING! Risk of injury or suffocation. • Disconnect the appliance from the mains supply. • Cut off the mains cable and discard it. • Remove the door catch to prevent children and pets to get closed in the appliance.
-
Page 5: Easy Start
EASY START On/off indicator Start button Programme marker Programme knob Indicators Delay button INDICATORS Washing phase. It comes on when the washing phase operates. Drying phase. It comes on when the drying phase operates. End indicator. Salt indicator. It is always off while the programme operates. -
Page 6: Information For Test Institutes
PROGRAMMES Consumption values Degree of soil Programme Programme phases Type of load Duration Energy Water (min) (kWh) Normal soil • Prewash 1.039 Crockery and • Wash 50 °C cutlery • Rinses • Heavy soil • Prewash 150 - 1.5 - 1.6 13 - 15 Crockery, cut- •... -
Page 7: The Water Hardness Table
Do not use detergent and do not load the baskets. THE WATER HARDNESS TABLE German degrees French degrees Water softener mmol/l Clarke degrees (°dH) (°fH) level 47 -50 84 - 90 8.4 - 9.0 58 - 63 43 - 46 76 - 83 7.6 - 8.3 53 - 57... -
Page 8: Adding Salt
• Release when start to flash. • Press . Indicators flash. The current setting is indicated by the intermittent flashing of the indicator : e.g. 5 intermittent flashes + pause + 5 intermittent flashes = level 5. • Press to change the setting. Each time you press the button, the level increases. After level 10 you will start again from level 1. -
Page 9: Adding Detergent
ADDING DETERGENT If the programme has a prewash phase, put a small quantity of detergent also in compartment B. ADDING MULTI-TABLETS • Do not fill the salt container and the rinse aid dispenser. • Adjust the water softener to the lowest level. •... -
Page 10: Starting A Programme
STARTING A PROGRAMME Open the water tap, close the door, select a programme, press OPTION DELAY With this option you can postpone the start of a programme of 3 hours. Set the programme, press Delay. Press to start the countdown. At the end of the countdown, the programme starts. -
Page 11: Hints And Tips
AT THE END OF THE PROGRAMME 5 min The indicator comes on. If you do not deactivate the appliance within 5 minutes all indicators goes off. This helps to decrease energy consumption. Turn the knob to . Close the tap. HINTS AND TIPS GENERAL THE WATER SOFTENER... -
Page 12: Unloading The Baskets
• Detergent tablets do not fully dissolve with short • Make sure that cutlery and dishes do not bond programmes. To prevent detergent residues on together. Mix spoons with other cutlery. the tableware, we recommend that you use the • Make sure that glasses do not touch other tablets with long programmes. -
Page 13: Troubleshooting
CLEANING THE FILTERS • Make sure that there are no residues of food or soil in or around the edge of the sump. • Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. •... - Page 14 The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre. Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket.
-
Page 15: The Washing And Drying Results Are Not Satisfactory
Problem and alarm code Possible cause and solution The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneous- ly all the appliances in use. Check the socket am- perage and the capacity of the meter or turn off one of the appliances in use. -
Page 16: Technical Information
Problem Possible cause and solution Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. There are residues of detergent •... -
Page 17: Environment Concerns
RATING PLATE INFORMATION FOR TEST INSTITUTES For all the necessary information for test performance, send an email to: info.test@dishwasher-production.com Write down the product number (PNC) that is on Mod..the rating plate. Prod. No..Ser. - Page 20 WWW.ZANUSSI.COM/SHOP...