Advertisement
IMPORTANT SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Fan.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!
ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the
outlet and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this
condition should be replaced by a qualified electrician.
ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole
means of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and
unplug the Fan when not in use.
BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The Blue Plug™ on your Lasko fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be
removed or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace,
repair or tamper with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device
incorporated in this plug.
THIS FAN HAS A POLARIZED PLUG (one blade is wider than the other). This plug is designed to fit into the outlet only one
way. Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety fea-
ture. If the plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced.
CAUTION
• AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these
devices may overheat and cause a fire hazard.
•DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire
hazard.
•ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
•NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
•DO NOT block, cover or obstruct air flow to or from the fan while in operation.
•DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location
may create a shock hazard.
•DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will not be tripped over.
•NEVER use a single extension cord to operate more than one Fan or other electrical device.
•DO NOT use this Fan if it has been damaged or is not functioning properly.
•Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,
move the Fan to another location.
•Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).This Fan is not suitable for use in agricultural
facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article
547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).This Fan is not suitable for use in hazardous
locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient
or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the
user's authority to operate this equipment.
SAVE THESE INSTRUCTIONS
Rev. M 10/17
2
Video Tutorial de Ensamblaje:
Escanee con un teléfono inteli-
gente o visita nuestra página
www.laskoproducts.com/how-to
ARMADO
1. Saque el conjunto de la tubería del cartón como muestra. (Figura 1)
2. Desafloje la Tuerca de Ajuste de Altura, girando en sentido contrahorario.
(Figura 2)
3. Eleve la Extensión De La Tubería. (Figura 3)
4. Apriete la Tuerca de Ajuste de Altura, girando en sentido horario. (Figura 4)
5. Utilizando un movimiento giratorio, inserte el extremo del tubo de diámetro
grande en el agujero de la Base. (Figura 5) El girar el tubo a medida que se
lo empuja asegura que el tubo quede plenamente asentado en la Base.
Para ajustar la altura:
a) Afloje la Tuerca de Ajuste de Altura.
b) Eleve o baje el Tubo de Extensión hasta obtener la altura deseada.
c) Apriete la Tuerca de Ajuste de Altura.
6. Coloque el Conjunto de Cabezal con el Collar en el Tubo de Extensión.
(Figura 6)
7. Sostenga firmemente el Tubo de Extensión y empuje el Conjunto de Ca-
bezal hacia abajo con un movimiento giratorio hasta que quede asentado
en el Tubo de Extensión.
8. Inclinarla Cabeza del Ventilador hacia atrás. Coloque la Rejilla Trasera en
el Motor. (Figura 7) Alinear la lengüeta de la Rejilla Trasera con la ranura en
la parte superior de la cubierta delantera del Motor.
9. Asiente la Parrilla Trasera y sujetela con la Tuerca de Plástico hacia la
Derecha. Deslice la Helice en el Eje del Motor. (Figura 8) Alinear la
Ranura Del Cubo de la tapa con el Pasador del eje del motor. (Figura 8A)
10.
Para asegurar la Helice, enroscarla hasta que quede apretada en el
Cubo de la Tapa haciéndola girar Hacia la Izuierda.
11.
Con el cabezal del ventilador en posición vertical, alinee el Adorno de
la Parrilla Delantera de modo que quede horizontal y con el lado debido
hacia arriba. Empiece en la parte superior de la parrilla y siga hacia abajo,
insertando las Trabas de la Parrilla Trasera en las Ranuras de la Parrilla
Delantera. (Figura 9)
FUNCIONAMIENTO
1. Conecte la energía eléctrica a su ventilador pulsando el Botón Alimentación
( ).
2. VELOCIDAD DEL VENTILADOR: Ahora puede ajustar la velocidad del
ventilador al nivel deseado - 1 (baja), 2 (mediana) ó 3 (alta) - pulsando el
Botón Velocidad ( ).
3. FUNCIÓN DE TEMPORIZADOR: Este ventilador está equipado con un
temporizador. El temporizador puede ser programado 1, 2 o 4 horas.
Continúe oprimiendo el Botón Temporizador ( ) para lograr el tiempo
de programación deseado. Para cancelar el temporizador, presione el
botón del temporizador hasta que se apague la luz.
4. Después de apagar el Ventilador, desconecte la unidad del tomacorriente
eléctrico.
Este Ventilador puede hacerse funcionar mediante los Controles
Manuales ubicados en la parte superior de la unidad o con el Control
Remoto (se muestra en la Figura 13).
OSCILACION: Empuje la perilla ubicada en la parte superior de la caja del
motor para hacer que la cabeza del Ventilador se mueva de un lugar hacia
otro. (Figuras 10 y 11)
INCLINACION: Este Ventilador está equipado de Cabeza de Ventilador de ángulo
múltiple para la Circulación del aire por toda habitación o cuarto. Siga lo que
se indica a continuación para graduar propiamente el "ángulo de inclinación"
del Ventilador (Figura 13. Ponga una mano sobre el soporte exactamente por
debajo del Cuello del Ventilador. Ponga la otra mano sobre la parte superior del
Ventilador. Empuje o hale suavemente la Cabeza del Ventilador hasta que quede
en la posición deseada.
Tubería de
Extension
Tuerca de Ajuste de
Altura
Figura 1
Figura 2
Tubo de
Extensión
Tuerca de Ajuste
de Altura
Base
Figura 5
Rev. M 10/17
2085441
MODELO 1850
A
PRECAUCIÓN:
Cuando realice el ajuste de la altura después de
conectar el ensamblaje superior, SIEMPRE sos-
tenga el tubo de extensión con una mano, pues
al aflojar la tuerca de ajuste de la altura puede
causar la caída libre del tubo de extensión y el
ensamblaje superior.
Conjunto de
Cabezal
Collar
Tubo de
Extensión
Figura 6
R a n u r a
del Cubo
Figura 8A
Adorno
Ranuras
Figura 9
Hacia Arriba:
Figura 3
Figura 4
Estacionario
Figura 10
7
B
No tome tubos sepa-
rados. En caso de
tuberías se separa-
dos, insertar un tubo
en el tubo B.
Rejilla Trasera
Figura 7
Motor
Pasador
Rejilla
Helice
Trasera
Tapa de
Ventilador
Tuerca de
Figura 8
Plastico
Parrilla
Delantera
Parrilla
Trasera
Trabas
Hacia Adelante:
Oscilar
Figura 11
Figura 12
2085441
Advertisement
