Related Manuals for Seagate IRONWOLF ST16000VN001
Summary of Contents for Seagate IRONWOLF ST16000VN001
- Page 1 SATA Product Manual Standard 512E* models ST16000VN001 ST14000VN0008 100851636, Rev. B May 2019...
- Page 2 Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Raid Rebuild and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The FIPS logo is a certification mark of NIST, which does not imply product endorsement by NIST, the U.S., or Canadian governments.All other trademarks or registered trademarks are the property of their respective owners.
-
Page 3: Table Of Contents
Seagate® Technology Support Services ........ - Page 4 S.M.A.R.T. commands............. . 50 Seagate IronWolf SATA Product Manual, Rev. B...
-
Page 5: Seagate® Technology Support Services
For information regarding online support and services, visit: http://www.seagate.com/contacts/ For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/recover/ For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.com/partners/ Seagate IronWolf SATA Product Manual, Rev. B... -
Page 6: Introduction
Top Cover Attached motor for excellent vibration tolerance Worldwide Name (WWN) capability uniquely identifies the drive. NOTE Seagate recommends validating the configuration with the selected HBA/RAID controller manufacturer to ensure use of full capacity is supported. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 7: About The Serial Ata Interface
Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. The specification can be downloaded from www.serialata.org. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 8: Drive Specifications
Startup current (typical) 12V (peak) 1.8A Voltage tolerance (including noise) 5V ± 5% 12V ± 10% Operating temperature 5° to 70°C (Drive Reported Temperature) Non-Operating temperature –40° to 70°C (Ambient Temperature, see sections 2.6.1 and 2.15) Seagate IronWolf SATA Product Manual, Rev. B... - Page 9 Load-unload cycles (command controlled) 600,000 Supports Hotplug operation per Serial ATA Revision 3.3 specification * See Section 2.10, "Reliability" for rated MTBF device operating condition requirements. Seagate IronWolf SATA Product Manual, Rev. B...
-
Page 10: Formatted Capacity
Power-on to Ready (sec) (typ/max) 25/30 Standby to Ready (sec) (typ/max) 25/30 Ready to spindle stop (sec) (max) NOTE Power-on to ready time is based on typical operating conditions, and default full current spin-up profile. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 11: Power Specifications
Maximum DC 0.674 0.315 7.15 Maximum DC (peak) 0.843 0.943 *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 12: Conducted Noise
800 mV pp from 100 Hz to 8 KHz. 450 mV pp from 8 KHz to 20 KHz. 250 mV pp from 20 KHz to 5 MHz. 2.5.3 Voltage tolerance Voltage tolerance (including noise): 5V ± 5% 12V ± 10% Seagate IronWolf SATA Product Manual, Rev. B... -
Page 13: Extended Power Conditions - Powerchoice
Idle Immediate also provide a method to directly transition the drive into supported power conditions. PowerChoice exits power saving states under the following conditions Any command which requires the drive to enter the PM0: Active state (media access) Power on reset Seagate IronWolf SATA Product Manual, Rev. B... - Page 14 PowerChoice Supported Extended Power Condition Feature Subcommands EPC Subcommand Description Restore Power Condition Settings Go to Power Condition Set Power Condition Timer Set Power Condition State Enable EPC Feature Set Disable EPC Feature Set Seagate IronWolf SATA Product Manual, Rev. B...
-
Page 15: Environmental Limits
Non-operating –40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification assumes that the drive is packaged in the shipping container designed by Seagate for use with drive. 2.6.2 Humidity The values below assume that no condensation on the drive occurs. -
Page 16: Shock And Vibration
Linear Random Non-Operating Vibration The drive will not incur physical damage or have non-recoverable errors after being subjected to the power spectral density noise specified below. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 17: Acoustics
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 389-7) to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. -
Page 18: Reliability
The drives are recognized in accordance with UL/cUL 62368 -1 and EN 62368 -1. 2.11.2 Regulatory Models The following regulatory model number represent all features and configurations within the series: Regulatory Model Numbers: STL008 Seagate IronWolf SATA Product Manual, Rev. B... -
Page 19: European Union (Eu) Ce Marking Requirements
Morocco Commodity Mark To satisfy our OEM customers, Seagate has added the Moroccan Commodity Mark to the drives provided to the OEM for the sale of Customer Kits produced by our OEM customers that are intended to be incorporated into the OEM's finished system-level product by an end user. -
Page 20: Taiwanese Bsmi
As a subassembly, no Federal Communications Commission verification or certification of the device is required. Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. -
Page 21: China Requirements -China Rohs 2
The European Union REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) Regulation (EC) 1907/2006 regulates chemicals shipped into and used in Europe. A number of parts and materials in Seagate products are procured from external suppliers. We rely on the representations of our suppliers regarding the presence of REACH substances in these articles and materials. -
Page 22: Taiwan Requirements - Taiwan Rohs
CNS 15663, Guidance to reduction of the restricted chemical substances in electrical and electronic equipment. Seagate products must comply with the “Marking of presence” requirements in Section 5 of CNS 15663, effective January 1, 2018. This product is Taiwan RoHS compliant. -
Page 23: Reference Documents
Seagate’s option and at no charge to the customer, if returned by customer at customer’s expense to Seagate’s designated facility in accordance with Seagate’s warranty procedure. Seagate will pay for transporting the repair or replacement item to the customer. -
Page 24: Configuring And Mounting The Drive
For installations which require cables, users can connect the drive as illustrated in Figure Figure 2. Attaching SATA cabling Each cable is keyed to ensure correct orientation. IronWolf SATA drives support latching SATA connectors. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 25: Drive Mounting
MAX TORQUE 6 IN/LBS 4.000±.010 .140±.015 1.028 MAX [26.11MM] 2.000 C L OF DRIVE Figure 3. Mounting configuration dimensions NOTE The image is for mechanical dimension reference only and may not represent the actual drive. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 26: Serial Ata (Sata) Interface
The drive motor must come to a complete stop (Ready to spindle stop time indicated in Section 2.4) prior to changing the plane of operation. This time is required to insure data integrity. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 27: Serial Ata Device Plug Connector Pin Definitions
There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration. All used voltage pins (V ) must be terminated. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 28: Supported Ata Commands
Read Verify Sectors Extended Receive FPDMA Queued Request Sense Data Ext Remove Element And Truncate Sanitize Device - Crypto Scramble / 0011 (SED and ISE drives only) Sanitize Device - Overwrite Ext / 0014 Seagate IronWolf SATA Product Manual, Rev. B... - Page 29 (SED drives only) Trusted Send DMA (SED drives only) Trusted Receive (SED drives only) Trusted Receive DMA (SED drives only) Write Buffer Write DMA Write DMA Extended Write DMA FUA Extended Write FPDMA Queued Seagate IronWolf SATA Product Manual, Rev. B...
- Page 30 Serial ATA (SATA) interface Command name Command code (in hex) Write Log DMA Ext Write Log Extended Write Multiple Write Multiple Extended Write Multiple FUA Extended Write Sectors Write Sectors Extended Write Uncorrectable Extended Seagate IronWolf SATA Product Manual, Rev. B...
-
Page 31: Identify Device Command
(Bit 12: 1) Sanitize feature set supported - Y (Bit 11: 1) Commands allowed during sanitize op as specified in ACS-3 - Y (Bit 10: 1) Sanitize Antifreeze Lock Ext command supported - Y Seagate IronWolf SATA Product Manual, Rev. B... - Page 32 95–99 ATA-reserved 0000 100–103 Total number of user-addressable LBA sectors available. (see Section 2.2) These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFFFFFFFh. 104–105 ATA-reserved 0000 Seagate IronWolf SATA Product Manual, Rev. B...
- Page 33 230-233 Extended Number of User Accessible Sectors (see Section 2.2) 234-254 ATA-reserved 0000 Integrity word xxA5 NOTE See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data. Seagate IronWolf SATA Product Manual, Rev. B...
- Page 34 Ultra DMA mode 2 is currently active. Ultra DMA mode 3 is currently active. Ultra DMA mode 4 is currently active. Ultra DMA mode 5 is currently active. Ultra DMA mode 6 is currently active. Seagate IronWolf SATA Product Manual, Rev. B...
-
Page 35: Identify Device Data Log
Page number of the next supported ID data log page Page number of the last supported ID data log page 18..511 Reserved Copy of IDENTIFY DEVICE data 0..511 Copy of IDENTIFY DEVICE command data Seagate IronWolf SATA Product Manual, Rev. B... - Page 36 Supported Capabilities page information header (QWord) Shall be set to 1 0..7 62:24 Reserved 23:16 Page number 8..15 Supported Capabilities (QWord) Shall be set to 1 62:55 Reserved advanced background operation supported persistent sense data reporting sff-8447 reporting Seagate IronWolf SATA Product Manual, Rev. B...
- Page 37 Reserved read look-ahead supported volatile write cache supported smart supported flush cache ext supported Reserved 48-bit supported Reserved spin-up supported puis supported apm supported Reserved for CFA Seagate IronWolf SATA Product Manual, Rev. B...
- Page 38 Contents of the QWord are valid 32..39 62:4 Reserved nominal form factor 3.5” Write-Read-Verify Sector Count Mode 3 (QWord) Contents of the QWord are valid 40..47 62:32 Reserved 31:0 wrm mode 3 count Seagate IronWolf SATA Product Manual, Rev. B...
- Page 39 Contents of the QWord are valid 62:24 Reserved setting rate basis supported 22:9 Reserved 96..103 since power on rate basis supported Reserved power on hours rate basis supported Reserved date/time rate basis supported Seagate IronWolf SATA Product Manual, Rev. B...
- Page 40 Contents of the QWord are valid 128..135 62:32 Reserved 31:16 device maintenance polling time 15:0 abo recommended abo start interval Queue Depth (QWord) Contents of the QWord are valid 136..143 62:5 Reserved queue depth Seagate IronWolf SATA Product Manual, Rev. B...
- Page 41 Vendor Specific Supported Capabilities (QWord) 504..511 Contents of the QWord are valid 62:0 Vendor specific Current Settings Current Settings page information header (QWord) Shall be set to 1 0..7 62:24 Reserved 23:16 Page number Seagate IronWolf SATA Product Manual, Rev. B...
- Page 42 DMA Host Interface Sector Times (QWord) Contents of the QWord are valid 24..31 62:16 Reserved 15:0 dma sector time PIO Host Interface Sector Times (QWord) Contents of the QWord are valid 32..39 62:16 Reserved 15:0 pio sector time Seagate IronWolf SATA Product Manual, Rev. B...
- Page 43 47:32 time scheduled for device maintenance 31:16 time to performance degradation 15:0 minimum inactive time Advanced Background Operations Settings (QWord) Contents of the QWord are valid 80..87 62:8 Reserved abo_status 88..511 Reserved Seagate IronWolf SATA Product Manual, Rev. B...
- Page 44 FFFE Security Status (QWord) Contents of the QWord are valid 62:7 Reserved security supported master password capability 16..23 enhanced security erase supported security count expired security frozen security locked security enabled Seagate IronWolf SATA Product Manual, Rev. B...
- Page 45 (1, SED and ISE drives only) sanitize supported encrypt all supported 56..511 Reserved Parallel ATA 000..511 (Not supported for SATA drives) all zeros Serial ATA Seagate IronWolf SATA Product Manual, Rev. B...
- Page 46 Reserved sata gen3 signaling speed supported sata gen2 signaling speed supported sata gen1 signaling speed supported Seagate IronWolf SATA Product Manual, Rev. B...
- Page 47 (Word) SUPPORTED HARDWARE FEATURE CONTROL IDENTIFIER 44..47 Reserved Device Sleep Timing Variables (QWord) devslp timing variables supported 62:16 Reserved 48..55 15:8 devsleep exit timeout (deto) Reserved minimum devslp assertion time (mdat) 56..511 Reserved Seagate IronWolf SATA Product Manual, Rev. B...
-
Page 48: Device Statistics Log
Number of Reallocation Candidate Logical Sectors Number of High Priority Unload Events General Errors Statistics Number of Reported Uncorrectable Errors Number of Resets Between Command Acceptance and Command Completion Physical Element Status Changed Seagate IronWolf SATA Product Manual, Rev. B... - Page 49 Maximum Implicitly Open Zones Minimum Empty Zones Maximum Non Sequential Zones Zones Emptied Suboptimal Write Commands Commands Exceeding Optimal Limit Failed Explicit Opens Read Rule Violations Write Rule Violations 09..FE Reserved Vendor Specific Statistics Seagate IronWolf SATA Product Manual, Rev. B...
-
Page 50: Set Features Command
Disable use of SATA features Enable read look-ahead (read cache) feature (default). Report full capacity available NOTE At power-on, or after a hardware or software reset, the default values of the features are as indicated above. Seagate IronWolf SATA Product Manual, Rev. B... -
Page 51: Commands
S.M.A.R.T. Enable Operations S.M.A.R.T. Disable Operations S.M.A.R.T. Return Status NOTE If an appropriate code is not written to the Features Register, the command is aborted and 0x 04 (abort) is written to the Error register. Seagate IronWolf SATA Product Manual, Rev. B... - Page 52 Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 Publication Number: 100851636, Rev. B May 2019...