Advertisement
Information in this document is subject to
change without notice.
Sony, VAIO and CLIE are trademarks or regis-
tered trademarks of Sony. Microsoft, Windows,
Windows Media, Outlook, Bookshelf and other
Microsoft products are trademarks or registered
trademarks of Microsoft Corporation in the Unit-
ed States and other countries. The word Blue-
tooth and the Bluetooth logo are trademarks of
Bluetooth SIG, Inc. AMD, the AMD logo, other
AMD product names and combinations thereof
are trademarks of Advanced Micro Devices, Inc.
Intel Inside logo, Pentium, Celeron and Core are
trademarks or registered trademarks of Intel Cor-
poration. Transmeta, the Transmeta logo, Crusoe
Processor, the Crusoe logo and combinations
thereof are trademarks of Transmeta Corpora-
tion in the USA and other countries. Graffiti,Hot-
Sync, PalmModem, and Palm OS are registered
trademarks, and the Hotsync logo and Palm are
trademarks of Palm, Inc. or its subsidiaries. (M)
and Motrola are trademarks of Motrora, Inc. Oth-
er Motrola products and services with (R) mark
like Dragonball are the trademarks of Motrola,
Inc.
All other names of systems, products and ser-
vices in this manual are trademarks or registered
trademarks of their respective owners. In this
manual, the (TM) or (R) mark are not specified.
The components identified by mark contain
confidential information.
Strictly follow the instructions whenever the
components are repaired and/or replaced.
Caution Markings for Lithium/Ion Battery - The
following or similar texts shall be provided on
battery pack of equipment or in both the operat-
ing and the service instructions.
CAUTION: Danger of explosion if battery is in-
correctly replaced. Replace only with the same
or equivalent type recommended by the manu-
facturer. Discard used batteries according to the
manufacturer's instructions.
CAUTION: The battery pack used in this device
may present a fireor chemical burn hazard if mis-
treated. Do not disassemble, heat above 60°C
(140°F) or incinerate. Dispose of used battery
promptly. Keep away from children.
CAUTION: Changing the back up battery.
• Overcharging, short circuiting, reverse charg-
ing, multilation or incineration of the cells
must be avoided to prevent one or more of the
following occurrences; release of toxic mate-
rials, release of hydrogen and/or oxygen gas,
rise in surface temperature.
• If a cell has leaked or vented, it should be re-
placed immediately while avoiding to touch it
without any protection.
Service and Inspection Precautions
1. Obey precautionary markings and
instructions
Labels and stamps on the cabinet, chassis, and
components identify areas requiring special pre-
cautions.
Be sure to observe these precautions, as well as
all precautions listed in the operating manual and
other associated documents.
2. Use desinated parts only
The set's components possess important safety
characteristics, such as noncombustibility and
the ability to tolerate large voltages. Be sure that
replacement parts possess the same safety char-
acteristics as the originals. Also remember that
the
mark, which appears in circuit diagrams
and parts lists, denotes components that have
particularly important safety functions; be extra
sure to use only the designated components.
3. Always follow the original design
when mounting parts and routing
wires
The original layout includes various safety fea-
tures, such as inclusion of insulating materials
(tubes and tape) and the mounting of parts above
the printer board. In addition, internal wiring has
been routed and clamped so as to keep it away
from hot or high-voltage parts. When mounting
parts or routing wires, therefore, be sure to dupli-
cate the original layout.
- 2 -
4. Inspect after completing service
After servicing, inspect to make sure that all
screws, components, and wiring have been re-
turned to their original condition. Also check
the area around the repair location to ensure that
repair work has caused no damage, and confirm
safety.
5. When replacing chip compo-
nents...
Never reuse components. Also remember that
the negative side of tantalum capacitors is easily
damaged by heat.
6. When handling flexible print
boards...
• The temperature of the soldering-iron tip
should be about 270°C.
• Do not apply the tip more than three times to
the same pattern.
• Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are
easily damaged by vibration. Always handle
with care.
ATTETION AU COMPOSANT AYANT RAP-
PORT À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE
MARQUE
SUR LES DIAGRAMMES SCHÉ-
MATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIÈSES SONY DONT
LES NUMÉROS SONT DONNÉSDANS CE
MANUEL OU DANS LES SUPPÉMENTS PUB-
LIÉS PAR SONY.
Sony Confidential
SVT212 Series (9-890-977-XX)
Advertisement
