Room Temperature Adjustment; Fan Speed Adjustment; Ventilation; Others - Mitsubishi Electric CITY MULTI PEFY-WP32VMA-E Operation Manual

For fan
Press the 3 [Mode (BACK)] Button and bring up the "
• The fan operation functions to circulate the air in the room.
• The temperature of the room cannot be set by fan operation.
Caution:
Never expose your body directly to cool air for a long time. Excessive expo-
sure to cool air is bad for your health, and should therefore be avoided.
Dry operation
The dry is a microcomputer-controlled dehumidifying operation which controls
excessive air-cooling according to the room temperature of your choice. (Not usable
for heating.)
1. Until reaching room temperature of your choice
The compressor and indoor fan function is linked motion according to the
change of the room temperature and automatically repeat ON/OFF.
2. When reaching room temperature of your choice
Both the compressor and indoor fan stop.
When stop continues for 10 minutes, the compressor and indoor fan are oper-
ated for 3 minutes to keep the humidity low.
For heating
Press the 3 [Mode (BACK)] Button to bring up the "
Regarding displays during heating operation "DEFROST"
Displayed only during the defrosting operation.
"STAND BY"
Displayed from the start of heating operation until the moment warm air blows out.
Caution:
• When the air-conditioner is used together with burners, thoroughly venti-
late the area. Insufficient ventilation can result in accidents due to oxygen
deficiency.
• Never place a burner at a place where it is exposed to the airflow from the
air-conditioner.
Doing so can result in imperfect combustion of the burner.
• The microcomputer functions in the following cases:
• Air does not blow out when heating starts.
- To prevent any cool air from escaping, the indoor fan is gradually switched in
sequence from faint airflow/weak airflow/set airflow according to the tempera-
ture rise of the blown out air. Wait a moment until the airflow comes out naturally.
• The fan is not moving at the set speed.
- In some models, the system switches over to faint airflow when the temper-
ature of the room reaches the set temperature. In other cases, it stops to pre-
vent any cool air from escaping during the defrosting operation.
• Air flows out even if operation is stopped.
- Approximately 1 minute after the stop of operation, the indoor fan sometimes
rotates to eliminate extra heat generated by the electric heater, etc.
The fan speed comes to low or high.

4. The smart way to use

Even minimal steps to care for your air conditioner can help make its use far
more effective in terms of air-conditioning effect, electricity charges, etc.
Set the right room temperature
• In cooling operation, a temperature difference of about 5 °C between indoors and
outdoors is optimum.
• If the room temperature is raised by 1 °C during air-cooling operation, about 10 %
electric power can be saved.
• Excessive cooling is bad for health. It also results in the waste of electric power.
Clean the filter thoroughly
• If the screen of the air filter becomes clogged, the airflow and air-conditioning
effect can be significantly reduced.
Further, if the condition is left unattended, failure can result. It is particularly impor-
tant to clean the filter at the beginning of the cooling and heating seasons. (When
profuse dust and dirt have accumulated, clean the filter thoroughly.)

3.3. Room temperature adjustment

FAN" display.
To change room temperature
Press the 1 [Set Temperature] Button and set the room temperature of your
choice.
Pressing
If the pressing is continued, the setting continues to change by 1 °C.
• Indoor temperature can be set within the following range.
• Temperature cannot be set for the fan mode.
* The range of room temperature display is 8 °C - 39 °C. Outside this range, the dis-
play flashes either 8 °C - 39 °C to inform you if the room temperature is lower or
higher than the displayed temperature.

3.4. Fan speed adjustment

To change fan speed
Every time you press the 6 [Fan Speed] button once, it switches from the low-speed
to high-speed settings successively.
In the electronics dry operation, the indoor fan automatically turns to low-speed oper-
HEAT" display. ation. Switching of fan speed is impossible. (Only the display on the remote controller
changes.)
* Every time the fan speed adjustment button is pressed once, the fan speed is
changed.
Fan speed : 3 stages
Display:
* This setting can be adjusted only with MA remote controller.

3.5. Ventilation

• The ventilation unit (OA processing unit or LOSSNAY) automatically goes into
operation when the indoor unit that is interlocked with it goes into operation.
• If the 8 [Ventilation] button is pressed while the indoor unit is stopped, only the
ventilator goes into operation.
• Press the 8 [Ventilation] button to change the fan speed.
• Depending on the models, the indoor unit fan goes into operation while the unit is
in the ventilation mode.

3.6. Others

Prevent intrusion of heat during air-cooling
• To prevent the intrusion of heat during cooling operation, provide a curtain or a
blind on the window to block out direct sunlight. Also, do not open the entrance or
exit except in cases of dire necessity.
Carry out ventilation sometimes
• Since the air periodically gets dirty in a room that is kept closed for a long time,
ventilation is sometimes necessary. When gas appliances are used together with
the air conditioner, special precautions must be taken. If the "LOSSNAY" ventila-
tion unit developed by our company is used, you can perform ventilation with less
waste. For details on this unit, consult with your dealer.
or once changes the setting by 1 °C.
Cooling/dry :19 °C - 30 °C
Heating :17 °C - 28 °C
(Low) (Mid)
: Displayed when control is executed by a separately
sold centralized control unit, etc.
: Displayed from the start of heating operation until the
moment warm air blows out.
: This displays indication when some abnormality
occurs in the unit.
: When a Button is pressed for any function which the
indoor unit cannot perform, this display flashes concur-
rently with the display of that function.
: In the system in which the [Sensor] display is indicated
as the "remote controller", room temperature measure-
ment is performed by the room temperature sensor
built into the remote controller.
: Displayed when it is time to clean the filter.
Press the a [FILTER ( )] Button twice, then the dis-
play is disappeared.
(High) (AUTO*)
7