Summary of Contents for Radial Engineering B-RAD X 7000
- Page 1 EN - V1.0 TURK B-RAD X USER MANUAL USER MANUAL FOR: • B-RAD X 7000 • B-RAD X 10K • B-RAD X 15K WWW.RADIALTORQUE.EU...
-
Page 2: Table Of Contents
B-RAD X User manual TABLE OF CONTENTS General Instructions ................4 General Power Tool Safety Warnings ........5 Battery Pack Safety Warnings ............6 1. General Information ..............8 1.1 System Components ............8 1.2 Specifications ................8 1.2.1 Tool Model Specifications .........8 1.2.2 Battery Specifications ..........8 1.2.3 Environmental Specifications .........9 1.2.4 Cycle of Operation ............9 2. - Page 3 B-RAD X User manual 3.3 Basic Level Menu Options ..........16 3.3.1 Information Menu ............16 3.4 Advanced Level Menu Options........16 3.4.1 Configuration Menu ..........16 3.4.2 Change Torque Units ..........16 3.4.3 LED Display Brightness .......... 17 3.4.4 The 2-Hand Safety Setting ........17 3.4.5 Back-Off Setting ............
-
Page 4: General Instructions
B-RAD X User manual GENERAL INSTRUCTIONS NOTE: Do not operate the tool before reading these instructions. If breakdown, malfunction or damage occurs, do not attempt to repair, please contact Radial Torque Tools B.V. immediately. RAD battery torque wrenches are reversible, non-impacting, torque controlled tightening tools and must always be operated with the following: •... -
Page 5: General Power Tool Safety Warnings
B-RAD X User manual 3. Personal Safety Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. -
Page 6: Battery Pack Safety Warnings
B-RAD X User manual accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may show unpredictable behaviour resulting in fire, explosion, or risk of injury. -
Page 7: General Information
B RAD X User manual 1. General Information 1.1. System Components The B-RAD X Tool System is shipped in a custom foam-lined storage case with the following parts: • B-RAD X Tool (Figure 1.1-1) • Two RAD HD Battery Packs (Figure 1.1-2) •... -
Page 8: Specifications
B-RAD X User manual 1.2. Specifications 1.2.1. Tool Model Specifications The following table outlines the torque ranges, speed, and weight of the BRAD X models. Weight Tool Model Torque Range (Imperial) Torque Range (Metric) Speed (incl. battery) B-RAD X 5000 / 7000-M 500 –... -
Page 9: Environmental Specifications
B-RAD X User manual 1.2.3. Environmental Specifications CAUTION! Only operate the B-RAD X Tool System if the following storage and operation conditions have been met. All Models Ambient Operating Temperature Range 0 – 40 32 – 104 Storage Temperature Range -20 –... -
Page 10: Tool System
B RAD X User manual 2. Tool System The following sections introduce the operation of the Tool Handle, Reaction Arm, LED Display Interface, RAD HD Battery Pack, and RAD Battery Charger. 2.1. Tool Handle The B-RAD X (Figure 2.1-1) is activated with a Trigger Switch. Torque values and tool information are displayed on 5-digit LED display. -
Page 11: Keypad
B RAD X User manual 2.2.1. Keypad The keypad consists of 4 buttons that are located on either side of the LED Display. • Enter Button: used to open the main menu and enter the sub-menus. It is also used to save a value that has been set. -
Page 12: Rad Hd Battery Pack
B RAD X User manual 2.3. RAD HD Battery Pack CAUTION! Only use the RAD HD Battery Pack with the B-RAD X Tool System. Using third-party batteries may damage the B-RAD X Tool System. Keep the RAD HD Battery Pack away from any metal objects. If the battery terminals are connected by a metal object, the battery will short and cause damage to the battery and injury to the operator. -
Page 13: Rad Battery Charger
B RAD X User manual 2.4. RAD Battery Charger CAUTION! The RAD HD Battery Pack should only be charged on the RAD Battery Charger. If an incompatible charger is used, damage to the RAD HD Battery will occur. The Charging Status Display (Figure 2.4-1) indicates when the RAD HD Battery is charging, when the charge is complete, and if there is an error. -
Page 14: Interface And Settings
B RAD X User manual 3. Interface and Settings CAUTION! The B-RAD X must be calibrated before first use. If the LED Display shows anything other than the Torque Select screen, the Information Menu, or the Calibration Menu, contact Radial Torque Tools B.V. Technical Support (refer to Section 6. -
Page 15: Unlocking Access Levels
B RAD X User manual 3.1.1. Unlocking Access Levels The B-RAD X has several diff erent access levels. Table 3.1.1-1 below defi nes the names of access levels, their use cases, and corresponding codes. To change access levels: 1. Long press Enter to bring up the Main menu. 2. -
Page 16: Basic Level Menu Options
B RAD X User manual 3.3. Basic Level Menu Options The Basic Level Menu Options are limited to the Lock Menu and the Information Menu. 3.3.1. Information Menu The Information menu displays values for Gearbox, Torque Units, Low End, High End, Serial Number and Firmware Version. -
Page 17: Led Display Brightness
B RAD X User manual 3.4.3. LED Display Brightness See Section 3.4.1 Confi guration Menu to navigate to the sub-menu this option is located in. The Brightness menu is used to adjust the brightness level of the LED Display. To change the brightness level of the LED Display: Enter. -
Page 18: Back-Off Setting
B RAD X User manual 3.4.5. Back-Off Setting See Section 3.4.1 Confi guration Menu to navigate to the sub-menu this option is located in. The Back-Off menu is used to set a value in degrees for the tool to reverse rotation after the tool achieves the set torque. -
Page 19: Display Mode - Torque Vs. Table
B RAD X User manual 3.5. Display Mode – Torque vs. Table The B-RAD X Tool System has two diff erent Display Modes that can be toggled between. There is Basic Display Mode known as the Torque Mode and Select Display Mode known as Table Mode. Note: The B-RAD X Tool System’s is by default set to Basic Display Mode (Torque Mode). -
Page 20: Menu Tree - Overview
B RAD X User manual 3.6. Menu Tree - Overview Table 3.6-1 is an overview of the Menu system that can be seen in Basic and Advanced Access Levels. With help navigating the menus See Section 3.2.3 Menu Navigation. Note: A bold description means it will take you to the next menu tree level. -
Page 21: General Operating Instructions
B RAD X User manual 4. General Operating Instructions CAUTION! Only qualified personnel with training in the safe operation of torque tooling and the B-RAD X should operate this tool. Refer to the Important Safety Notice for more information. 4.1. Reaction Arm WARNING! Always keep body parts clear of the Reaction Arm when the B RAD X is in use. -
Page 22: Reaction Points
B RAD X User manual Reaction Points Make sure that the Reaction Arm is in contact with a solid Reaction Point before you operate the tool. When the tool is in operation, the Reaction Arm rotates in the opposite direction to the Output Square Drive and must be allowed to rest squarely against a solid object or surface adjacent to the bolt to be tightened. -
Page 23: Reaction Arm Foot
B RAD X User manual Reaction Arm Foot Ensure that the foot of the Reaction Arm aligns with the reaction point. CORRECT: The foot of the Reaction Arm aligns with the reaction point. The length of the foot cannot be shorter or longer than the reaction point. INCORRECT: The reaction point is too close in the left image and too far in the right image. -
Page 24: Troubleshooting
B-RAD X User manual 5. Troubleshooting CAUTION! Disassembling or attempting repair will void warranty. If breakdown, malfunction, or error occurs, contact Radial Torque Tools B.V. Technical Support (refer to Section 6. Contact Us). The Display Module may show abnormal behaviour depending on operating conditions, frequency of use, or excessive wear on the Display Module. -
Page 25: Faults
B-RAD X User manual 5.1.2 Faults When you see a fault, it is followed by a number. This indicates a hardware anomaly has occurred and the tool needs to be sent to the nearest repair facility for repairs. Contact Radial Torque Tools B.V. or a RAD distributor, report the fault code and describe the conditions before the fault occurred to determine if the tool needs to be sent for repair. - Page 26 B-RAD X User manual NOTES V1.0 - May 2023...
- Page 27 B-RAD X User manual NOTES V1.0 - May 2023...
- Page 28 THE EXCLUSIVE MASTER DISTRIBUTOR FOR RAD TORQUE SYSTEMS IN EAST- AND WESTERN EUROPE (EXCLUDING THE UK), NORTH AFRICA AND CENTRAL ASIA: Radial Torque Tools B.V. Phone: +31 (0)35 - 588 24 50 Zuidergracht 19 Mail: sales@radialtorque.eu 3763 LS Soest - The Netherlands WWW.RADIALTORQUE.EU...