Asus TUF GAMING B560M-PLUS WIFI Manual page 13

• M.2_1 slot (Key M), type 2242/2260/2280 (Only Intel
PCIe 4.0 x4 mode, this slot will be disabled for other CPUs)
• M.2_2 slot (Key M), type 2242/2260/2280 (supports PCIe 3.0 x4 & SATA modes)
• To enable Intel
PCH-attached slots with Intel
• M.2_2 slot shares bandwidth with SATA6G_2.When M.2_2 slot is operating in SATA
mode, SATA6G_2 will be disabled.
7. SATA 6Gb/s ports
The SATA 6Gb/s ports allow you to connect SATA devices such as optical disc drives and
hard disk drives via SATA cables.
8. USB 3.2 Gen 1 connector (supports USB Type-C
The USB 3.2 Gen 1 connector (USB Type-C
USB 3.2 Gen 1 module for an additional USB 3.2 Gen 1 Type-C
The connector provides a data transfer speed of up to 5 Gb/s.
9. USB 3.2 Gen 1 header
The USB 3.2 Gen 1 header allows you to connect a USB 3.2 Gen
1 module for additional USB 3.2 Gen 1 ports. The USB 3.2 Gen 1
header provides data transfer speeds of up to 5 Gb/s.
The USB 3.2 Gen 1 module is purchased separately.
10. USB 2.0 headers
The USB 2.0 headers allow you to connect a USB module for additional USB
2.0 ports. The USB 2.0 headers provide data transfer speeds of up to 480 Mb/s.
DO NOT connect a 1394 cable to the USB connectors. Doing so will
damage the motherboard!
The USB 2.0 module is purchased separately.
11. AURA Addressable Gen 2 headers
The Addressable Gen 2 headers allow you to connect individually addressable
RGB WS2812B LED strips or WS2812B based LED strips.
The Addressable Gen 2 headers support WS2812B addressable RGB LED strips (5V/Data/
Ground), with a maximum power rating of 3A (5V), and the addressable headers on this
board can handle a combined maximum of 500 LEDs.
Before you install or remove any component, ensure that the power supply is switched off
or the power cord is detached from the power supply. Failure to do so may cause severe
damage to the motherboard, peripherals, or components.
ASUS TUF GAMING B560M-PLUS WIFI
Optane™ Memory (Hybrid Storage device), it must be installed in
®
Rapid Storage Technology.
®
) allows you to connect a
®
11 Gen processors support
® th
)
®
SBU2
SBU1
CC1
VBUS
port.
® RX1-
RX1+
GND
TX1-
TX1+
VBUS
USB3+5V
IntA_P2_SSRX-
IntA_P2_SSRX+
GND
IntA_P2_SSTX-
IntA_P2_SSTX+
GND
IntA_P2_D-
IntA_P2_D+
VBUS
TX2+
TX2-
GND
RX2+
RX2-
GND
D-
D+
CC2
PIN 1
USB3+5V
IntA_P1_SSRX-
IntA_P1_SSRX+
GND
IntA_P1_SSTX-
IntA_P1_SSTX+
GND
IntA_P1_D-
IntA_P1_D+
GND
PIN 1
ADD_GEN 2
PIN 1
1-3