Page 1
Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.
Note: The hand-held remote is not compatible with older Autohelm autopilots with an AH prefix (e.g. AH800). If you have any questions about compatibility, contact your nearest Raymarine dealer. Using the hand-held remote Note: You cannot use the hand-held remote to engage or disengage the autopilot.
Page 5
Connecting the hand-held remote The hand-held remote is connected directly to Raymarine autopilots or instruments using SeaTalk (the Raymarine data interface system). The remote is supplied with a waterproof plug and socket that can be installed anywhere a remote is required. The socket allows you to make connections directly to the autopilot or SeaTalk instrument, as described on the following pages.
Page 7
ST4000+ and ST5000+ autopilots ST4000+ and ST5000+ control units have two parallel SeaTalk ports. You can connect the hand-held remote to either of these ports. ST4000+ or ST5000+ Note: If any other SeaTalk instruments are connected to the ST4000 or ST5000 control units, the red wire (+12 V) must be connected to a separate 12 V supply fitted with a 5 A fuse.
Page 8
Owner’s Handbook ST6000+, ST6001+, ST7000+ and ST7001+ pilots ST6000+, ST6001+, ST7001+ or ST7000+ 150/400 Course Computer ST6000 and ST7000 autopilots The main difference when connecting older ST6000 and ST7000 autopilots is that you will need a SeaTalk cable with round plugs. ST6000 or ST7000 100/300 Course Computer ST6001+/ST6000+...
Page 9
SportPilot and SportPilot Plus To connect the hand-held remote to the SportPilot you will need to purchase an appropriate SeaTalk interface cable (D229). The red core should also be fitted with a 5 A fuse. SportPilot or SportPilot Plus 12 V Note: If you intend to locate the remote close to the SportPilot, the SportPilot’s power cable has two additional wires (yellow and screen) that you can use to connect the SeaTalk socket to the pilot.
Owner’s Handbook SeaTalk cables Because you can use the hand-held remote with a wide range of Raymarine autopilots, you will need to purchase the appropriate SeaTalk cable to connect the hand-held remote to the autopilot via the SeaTalk system. Extension cables - flat moulded plugs at each end Part no.
Page 11
Installing the SeaTalk socket 1. Apply the template onto the bulkhead as required. 2. Drill the 18 mm ( 3. Remove the template. 4. Cut and strip the SeaTalk cable (not supplied: see page 9). 5. Pass the cables through the bulkhead and wire to the socket, making sure the wires are connected to the correct pins.
Page 12
Owner’s Handbook Installing the hand-held remote bracket The hand- held remote is supplied with a bulkhead-mounted storing bracket. This bracket should be attached to a convenient bulkhead using the 3 double-sided adhesive pads provided. D5692-1 Note: Spare bulkhead brackets, part number D224, can be ordered from your dealer.
• Autopilot not in Auto mode. Note: No audible beep will be heard when operating the hand held remote. Spares List The following items may be purchased from your local Raymarine dealer should you need them. Part Number D161 D162...
Raymarine EMC Guidelines EMC Installation & Service Guidelines IMPORTANT NOTE All Raymarine equipment and accessories are designed to the best industry standards for use in the leisure marine environment. When powered up, all electrical equipment produces electromagnetic fields. These can cause adjacent pieces of electrical equipment to interact with one another, with a consequent adverse effect on operation.
Always use the ferrites supplied by Raymarine. Connections to Other Equipment If your Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite MUST always be fitted to the cable close to the Raymarine unit.
During this period, except for certain products, travel costs (auto mileage and tolls) up to 100 round trip highway miles (160 kilometres) and travel time of 2 hours, will be assumed by Raymarine only on products where proof of installation or commission by authorized service agents, can be shown.
Factory Service Centers United States of America Raymarine Inc 22 Cotton Road, Unit D Nashua, NH 03063-4219, USA Telephone: +1 603 881 5200 Fax: +1 603 864 4756 www.raymarine.com Sales & Order Services Telephone: +1 800 539 5539 Ext. 2333 or +1 603 881 5200 Ext.