Feit Electric S9DFL/850/MOT/BZ Manual

MODEL S9DFL/850/MOT/BZ & S9DFL/850/MOT/WH
Dual Head Motion Security Flood Light
IMPORTANT SAFETY INSTRUCTIONS AND INSTALLATION GUIDE
READ BEFORE INSTALLATION
SAVE THESE INSTRUCTIONS
This product may represent a possible shock or fire hazard if improperly installed
or attached in any way. Product should be installed in accordance with the owners
manual, current electrical codes and/or the current National Electric Code (NEC).
RISK OF ELECTRIC SHOCK: TURN OFF THE MAIN POWER AT
THE CIRCUIT BREAKER BEFORE INSTALLING.
(1)
EXTERNAL J BOX
(3)
INSTALLATION
(4)
(5)
(2)
FLUSH J BOX
(1)
INSTALLATION
(3)
(4)
(5)
(2)
1. J-box (Not Included) 5. Spacers (2 Pieces)
2. Ground Wire 6. Mounting Gasket
3. Mounting Bar 7. Mounting Plate
4. J-box Screws (2 Pieces) 8. Mounting Plate Screws
PARTS INCLUDED
REV005
FEIT ELECTRIC COMPANY | PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
WARNING:
(6) (7)
(13)
(10)
(14)
(9)
(8)
(11)
(12)
(6) (7)
(13)
(10)
(14)
(9)
(8)
(11)
(12)
9. Terminal Block 13. Fixture Body
10. Mounting Bar Screw (1 Piece) 14. Decorative Nuts (2pieces)
11. Mounting Holes 15. Motion And Photocell Sensor
12. Rubber Washers (2 Pieces)
TOOLS REQUIRED
PRE INSTALLATION
Remove the existing light fixture and disconnect house power supply wires.
EXTERNAL J BOX INSTALLATION
1.
Turn main power off at circuit breaker or fuse box.
2. Install mounting bar
(3) to an external j-box (1)
using provided j-box
screws (4) add spacer (5)
to eliminate gap
between mounting bar
and mounting plate.
3.
Extend and feed J-Box wires through openings on
mounting gasket (6) and mounting plate (7). Connect
ground (2) wire to the ground screw on the bracket as
shown below.
Note: Tear away at perforation on mounting gasket (6)
3
(6)
(2)
4. Secure mounting
gasket (6) and mounting
THIS SIDE UP
plate (7) to mounting
bar (3) using mounting
bar screw (10). Do not
over tighten
(15)
5.
Connect power supply
wires directly to terminal
block (9) secure wires to
terminal block by using a
small screwdriver.
Connect : black wire to "L"
input. White wire to "N" input.
6. Position and align the mounting holes (11) on
THIS SIDE UP
fixture body (13) to mounting plate screws (8). Secure
fixture body to mounting plate using decorative
rubber washers (12) and decorative nuts (14)
(15)
(12)
(8)
(13)
(11)
7
. Once fixture is tightly secured to j-box, apply a
silicone sealant around the base of the fixture to
prevent moisture from reaching the connections.
8 . Turn power on at circuit breaker to replace the fuse
FEIT ELECTRIC COMPANY | PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
INTERNAL FLUSH J BOX INSTALLATION
1.
Turn main power off at circuit breaker or fuse box.
2
(3)
2.
Install mounting bar
(4)
(3) to a j-box (1) using
provided j-box screws
(5)
(4) add spacer (5) to
eliminate gap between
mounting bar and
mountig plate.
3. Extend and feed j-box wires through openings on
mounting gasket (6) and mounting plate (7). Connect
ground (2) wire to the ground screw on the bracket as
shown below.
Note: Do not tear away at perforation on mounting gasket (6)
3
(7)
(2)
4
4.
Secure mounting
(10)
gasket (6) and mounting
plate (7) to mounting
bar (3) using mounting
bar screw (10). Do not
(7)
over tighten
(3)
(6)
5.
Connect power supply
5
wires directly to terminal
block (9) secure wires to
terminal block by using a
(9)
small screwdriver.
Connect : black wire to "L"
input. White wire to
"N" input.
6.
Position and align the mounting holes (11) on
fixture body (13) to mounting plate screws (8). Secure
fixture body to mounting plate using decorative
rubber washers (12) and decorative nuts (14)
(12)
(8)
(13)
(14)
(11)
7. Once fixture is tightly secured to j-box, apply a
silicone sealant around the base of the fixture to
prevent moisture from reaching the connections.
8
. Turn power on at circuit breaker to replace the fuse
2
(3)
(4)
(5)
(6)
(7)
4
(10)
(7)
(6)
5
(9)
(14)