Feit Electric S10.5DFL/850/MOT/BZ Important Safety Instructions And Installation Manual

MODEL S10.5DFL/850/MOT/BZ
2-Head Motion Security Flood Light
IMPORTANT SAFETY INSTRUCTIONS AND INSTALLATION GUIDE
READ BEFORE INSTALLATION
SAVE THESE INSTRUCTIONS
This product may represent a possible shock or fire hazard if improperly installed
or attached in any way. Product should be installed in accordance with the owners
manual, current electrical codes and/or the current National Electric Code (NEC).
RISK OF ELECTRIC SHOCK: TURN OFF THE MAIN POWER AT
THE CIRCUIT BREAKER BEFORE INSTALLING.
(2)
EXTERNAL J BOX
(5)
(4)
(3)
INSTALLATION
FLUSH J BOX
(2)
(5)
(4)
(3)
INSTALLATION
1. J-box (not included) 5. Mounting gasket
2. Mounting bar 6. Mounting plate
3. J-box screws (2 pieces) 7. Terminal block
4. Spacers (2 pieces) 8. Mounting plate screws (2 pieces)
PARTS INCLUDED
REV006
FEIT ELECTRIC COMPANY | PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
WARNING:
(6)
(7)
(10)
(8)
(9)
(13)
(12)
(11)
(6)
(7)
(10)
(8)
(9)
(13)
(12)
(11)
9. Mounting bar screw (1 piece) 13. Decorative nuts (2 pieces)
10. Fixture body 14. Motion and photocell sensor
11. Mounting holes
12. Decorative washers (2 pieces)
TOOLS REQUIRED
EXTERNAL J BOX INSTALLATION
1. Turn main power off at circuit breaker or fuse box.
2.
Install Mounting Bar (2)
to an External J-Box (1)
using provided J-Box
Screws (3). Add Spacer
(4) to eliminate gap
between Mounting Bar
and Mounting Plate.
3.
Extend and feed J-Box wires through openings
on Mounting Gasket (5) and Mounting Plate (6)
as shown below.
4.
Secure Mounting
Gasket (5) and
Mounting Plate (6)
to Mounting Bar (2)
using Mounting Bar
Screw (9). Do not over-tighten.
5. Connect power supply
wires directly to
Terminal Block (7).
Secure wires to
THIS SIDE UP
Terminal Block by using
a small screwdriver.
(14)
See below.
Connect:
Black wire to
"L" input.
Ground wire to
"GND" input.
White wire to
"N" input.
6. Position and align the Mounting Holes (11) on
Fixture Body (10) to the Mounting Plate Screws (8).
Secure Fixture Body to Mounting Plate using
Rubber Washers (12) and Decorative Nuts (13).
THIS SIDE UP
(8)
(14)
(11)
7.
Once fixture is tightly secured to J-Box, apply a
silicone sealant around the base of the fixture to
prevent moisture from reaching the connections.
8.
Turn power on at circuit breaker or replace the fuse.
FEIT ELECTRIC COMPANY | PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
FLUSH J BOX INSTALLATION
1. Turn main power off at circuit breaker or fuse box.
(1) (2)
2.
(3) Install Mounting Bar (2)
to a Flush J-Box (1)
using provided J-Box
(4)
Screws (3). Add Spacer
(4) to eliminate gap
between Mounting Bar
and Mounting Plate.
3.
Extend and feed J-Box wires through openings
on Mounting Gasket (5) and Mounting Plate (6)
as shown below.
(6)
(5)
(4)
N
D
N
G
L
(2)
(6)
4.
Secure Mounting
Gasket (5) and
(9)
Mounting Plate (6)
N
D
N
G
L
to Mounting Bar (2)
using Mounting Bar
Screw (9). Do not over-tighten.
(5)
5. Connect power supply
(7)
wires directly to
Terminal Block (7).
Secure wires to
Terminal Block by using
a small screwdriver.
See below.
See detail below
Connect:
Detail
Black wire to
"L" input.
Ground wire to
"GND" input.
L GND N
White wire to
"N" input.
6. Position and align the Mounting Holes (11) on
Fixture Body (10) to the Mounting Plate Screws (8).
Secure Fixture Body to Mounting Plate using
Rubber Washers (12) and Decorative Nuts (13).
(10)
(12) (13)
7.
Once fixture is tightly secured to J-Box, apply a
silicone sealant around the base of the fixture to
prevent moisture from reaching the connections.
8.
Turn power on at circuit breaker or replace the fuse.
(2)
(3)
(1)
(4)
(5)
(6)
(4)
N
D
N
G
L
(2)
(6)
(4)
(9)
N
D
N
G
L
(5)
(7)
See detail below
Detail
L GND N
(10)
(8)
(11) (12) (13)