Adjusting The Electronic Speed Control - Traxxas 68086-4 Owner's Manual

ADJUSTING THE ELECTRONIC SPEED CONTROL

VXL-3s Battery Settings (Low-Voltage Detection Setting)
The Velineon VXL-3s electronic speed control is equipped with built-in Low-Voltage
VXL-3s Specifications
Detection. The Low-Voltage Detection circuitry constantly monitors the battery
Input voltage:
voltage. When the battery voltage begins to reach the minimum recommended
4.8-11.1V (4 to 9 cells
discharge voltage threshold for LiPo battery packs, the VXL-3s will limit the power
NiMH or 2S to 3S LiPo)
output to 50% throttle. When the battery voltage attempts to fall below the
Supported Motors:
minimum threshold, the VXL-3s will shut down all motor output. The LED on the
Brushless
speed control will slowly blink red, indicating a low-voltage shutdown. The VXL-3s
Motor limit:
will stay in this mode until a fully charged battery is connected.
None
The VXL-3s speed control's Low-Voltage Detection has been disabled for best
Continuous current:
performance with NiMH batteries. The speed control's LED will glow red when it
200A
is turned on, indicating Low-Voltage Detection is disabled. Be certain to activate
Peak current :
Low-Voltage Detection if you install a LiPo battery in your model.
320A
batteries while Low-Voltage Detection is disabled.
BEC voltage:
To verify the Low-Voltage Detection setting:
6.0V DC
1. Turn on the transmitter (with the throttle at neutral).
Transistor type:
2. Connect a fully charged battery pack to the VXL-3s.
MOSFET
3. Press and release the EZ-Set button to turn the VXL-3s on. If the LED is solid red,
Battery connector:
then the Low-Voltage Detection is DISABLED (not safe to use LiPo batteries). If
Traxxas High-Current
the LED is solid green, then Low-Voltage Detection is ACTIVATED.
Connector
To activate Low-Voltage Detection (LiPo setting):
Motor connectors:
1. Make sure the LED on the VXL-3s is on and red.
TRX 3.5mm bullet
2. Press and hold the EZ-Set button for ten seconds. The
connectors
LED will turn off and then light green. Also, a "rising"
Motor/Battery Wiring:
musical tone will be emitted from the motor.
12-gauge Maxx ® Cable
3. Low-Voltage Detection is now ACTIVATED.
Thermal Protection:
To disable Low-Voltage Detection (NiMH setting):
2-stage thermal shutdown
1. Make sure the LED on the VXL-3s is on and green.
2. Press and hold the EZ-Set button for ten seconds. The
LED will turn off and then light red. Also, a "falling"
musical tone will be emitted from the motor.
3. Low-Voltage Detection is now DISABLED.
Transmitter Adjustments for the VXL-3s ESC
Before attempting to program your VXL-3s ESC, it is important to make sure that
your transmitter is properly adjusted (set back to the factory defaults). Otherwise,
you may not get the best performance from your speed control.
The transmitter should be adjusted as follows:
If the transmitter settings have been adjusted, reset them to the factory defaults.
1. Turn the transmitter off.
2. Hold both MENU and SET.
3. Turn the transmitter on.
4. Release MENU and SET. The transmitter LED will blink red.
5. Press SET to clear settings. The LED will turn solid green and the transmitter is
18 • SLASH 4x4
restored to default.
VXL-3s Setup Programming (Calibrating your ESC and transmitter)
Read through all of the programming steps before you begin. If you get lost during
programming or receive unexpected results, simply unplug the battery, wait a few
seconds, plug the battery back in, and start over.
1. Connect a fully charged battery pack to the VXL-3s.
2. Turn on the transmitter (with the throttle at neutral).
3. Press and hold the EZ-Set button (A). The LED will first turn
green and then red. Release the EZ-Set button.
4. When the LED blinks RED ONCE, pull the throttle
trigger to the full throttle position and hold it there (B).
5. When the LED blinks RED TWICE, push the throttle
trigger to the full reverse and hold it there (C).
Never use LiPo
6. When the LED blinks GREEN ONCE, programming
is complete. The LED will then shine green or red
(depending on Low-Voltage Detection setting),
indicating the VXL-3s is on and at neutral (D).
VXL-3s Operation
To operate the speed control and test programming, place the
vehicle on a stable block or stand so that all of the drive wheels are
off the ground. Disconnect motor wires "A" and "C" (see page 12), this will ensure
the motor does not drive the wheels during testing. Do not test programming
without disconnecting the motor wires.
Note that in steps 1-7 below, Low-Voltage Detection is DISABLED (factory default)
and the LED shines red. If Low-Voltage Detection is ACTIVATED, the LED will shine
green instead of red in steps 1-7 below. Never use LiPo batteries while Low-Voltage
Detection is disabled.
1. With the transmitter on, press and release the EZ-Set button. The LED will shine
red. This turns the VXL-3s on.
2. Apply forward throttle. The LED will turn off until full throttle power is reached.
At full throttle, the LED will illuminate red.
3. Move the trigger forward to apply the brakes. Note that braking control is fully
proportional. The LED will turn off until full braking power is reached. At full
brakes, the LED will illuminate red.
4. Return the throttle trigger to neutral. The LED will shine red.
5. Move the throttle trigger forward again to engage reverse (Profile #1).
The LED will turn off. Once full reverse power is reached, the LED
will illuminate red.
6. To stop, return the throttle trigger to neutral. Note that there is a programmed
delay when changing from reverse to forward. This prevents damage to the
transmission on high-traction surfaces.
7. To turn the VXL-3s off, press the EZ-Set button until the LED turns
off (.5 seconds).
A
Green then Red
B
Once Red
C
Twice Red
D
Once Green