Sears Craftsman 919.167312 Owner's Manual
Sears Craftsman 919.167312 Owner's Manual

Sears Craftsman 919.167312 Owner's Manual

Permanently lubricated single stage portable air compressor
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Owner's Manual
Permanently Lubricated
Single Stage
Portable
AIR COMPRESSOR
Model No.
919.167312
• Safety Guidelines
• Assembly
• Operation
• Maintenance
• Service and Adjustments
• Troubleshooting
• Repair Parts
CAUTION:
Read the Safety Guidelines
and All Instructions Carefully Before
Operating.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www.sears.com/craftsman
A09707
Rev. 1 12/22/05

Advertisement

Chapters

Table of Contents
loading

Summary of Contents for Sears Craftsman 919.167312

  • Page 1 • Maintenance • Service and Adjustments • Troubleshooting • Repair Parts CAUTION: Read the Safety Guidelines and All Instructions Carefully Before Operating. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Visit our Craftsman website: www.sears.com/craftsman A09707 Rev. 1 12/22/05...
  • Page 2: Table Of Contents

    If this CRAFTSMAN Air Compressor fails due to a defect in material or workmanship within one year from the date of purchase, Sears will at its option repair or replace it free of charge. Contact your nearest Sears Service Center (1-800-4-MY-HOME ® ) to arrange for repair, or return the Air Compressor to the place of purchase for replacement.
  • Page 3: Specification Chart

    SPECIFICATION CHART Model No. 919.167312 Running HP Bore 2.38" Stroke 1.35" Voltage-Single Phase 120V/60HZ/1PH Minimum Branch Circuit Requirement 15 amps Fuse Type Time Delay Air Tank Capacity Approx. Cut-In Approx. Cut-out SCFM @ 40 psig SCFM @ 90 psig Refer to Glossary for abbreviations SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand.
  • Page 4 IMPORTANT SAFETY INSTRUCTIONS Save these instructions Improper operation or maintenance of this product could result in serious injury and property damage. Read and understand all warnings and operation instructions before using this equipment. HAZARD WARNING: Risk of explosion or fire What Could Happen How To Prevent It Always operate the compressor in a...
  • Page 5 HAZARD WARNING: Risk of Bursting Air Tank: The following conditions could lead to a weakening of the tank, and result in a violent tank explosion and could cause property damage or serious injury. What Could Happen How To Prevent It Drain tank daily or after each use.
  • Page 6 HAZARD WARNING: Risk of Electrical Shock What Could Happen How To Prevent It Your air compressor is powered by Never operate the compressor outdoors electricity. Like any other electrically when it is raining or in wet conditions. powered device, If it is not used Never operate compressor with properly it may cause electric shock.
  • Page 7 HAZARD WARNING: Risk of Burns What Could Happen How To Prevent It Never touch any exposed metal parts Touching exposed metal such as the on compressor during or immediately compressor head or outlet tubes, can after operation. Compressor will remain result in serious burns.
  • Page 8 HAZARD WARNING: Risk of Serious Injury or Property Damage When Transporting Compressor (Fire, Inhalation, Damage to Vehicle Surfaces) What Could Happen How To Prevent It Oil can leak or spill and could result Always place COMPRESSOR on a in fire or breathing hazard; serious protective mat when transporting to injury or death can result.
  • Page 9: Glossary

    ACCESSORIES This unit is capable of powering the following Accessories. The accessories are available through the current Power and Hand Tool Catalog or full-line Sears stores. Accessories • Air Hose: 1/4", 3/8" or 1/2" I.D. in various lengths •...
  • Page 10: Assembly

    ASSEMBLY Unpacking Remove unit from carton and discard all packaging. INSTALLATION HOW TO SET UP YOUR UNIT Location of the Air Compressor Make sure the outlet being used Locate the air compressor in a clean, has the same configuration dry and well ventilated area. The air as the grounded plug.
  • Page 11 Extension Cords Voltage and Circuit Protection Using extension cords is not Refer to the specification chart for the recommended. The use of extension voltage and minimum branch circuit cords will cause voltage to drop requirements. resulting in power loss to the motor Risk of Unsafe and overheating.
  • Page 12: Operation

    OPERATION Know Your Air Compressor READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Outlet Pressure Tank Pressure Gauge Pressure...
  • Page 13 Air Compressor Pump (not shown): Motor Overload Protector: The Compresses air into the air tank. motor has an automatic reset Working air is not available until the thermal overload protector. If the compressor has raised the air tank motor overheats for any reason, the pressure above that required at the overload protector will shut "Off"...
  • Page 14 Move the On/Auto/Off lever How to Start: to "On/Auto" position. The Turn the On/Auto/Off lever compressor will start. to "On/Auto" and allow tank Run the compressor for 15 pressure to build. Motor will minutes. Make sure the drain stop when tank pressure reaches valve is open and there is "cut-out"...
  • Page 15: Maintenance

    MAINTENANCE Customer Responsibilities Daily Before Every Every or after each Yearly each hours hours Check Safety Valve Drain Tank Air Filter Air compressor pump intake and exhaust valves 1- more frequent in dusty or humid conditions Risk of Unsafe To Check Safety Valve Operation.
  • Page 16 After the water has been drained, IMPORTANT: Do not operate close the drain valve (clockwise). the compressor with the air filter The air compressor can now be removed. stored. If dirty, rinse air filter with warm NOTE: If drain valve is plugged, water and squeeze dry.
  • Page 17: Service And Adjustments

    SERVICE AND ADJUSTMENTS All maintenance and repair Unscrew the check valve (turn operations not listed must be counterclockwise) using a 7/8" performed by Trained Service open end wrench. Note the orientation for reassembly. Technician. Using a screwdriver, carefully Risk of Unsafe push the valve disc up and Operation.
  • Page 18 Assemble the regulator and To Replace Regulator orient as shown. Release all air pressure from air tank. See "To Drain Tank" in the Maintenance section. Set the On/Auto/Off lever to "Off" and unplug unit. Regulator Remove the outlet pressure gauge and quick connect (if equipped) from the regulator.
  • Page 19: Storage

    STORAGE Risk of Bursting. Before you store the air compressor, Water will make sure you do the following: condense in the air tank. If not Review the Maintenance section drained, water will corrode and on the preceding pages and weaken the air tank causing a risk perform scheduled maintenance of air tank rupture.
  • Page 20 TROUBLESHOOTING Risk of Unsafe Operation. Unit cycles automatically when power is on. When servicing, you may be exposed to voltage sources, compressed air, or moving parts. Before servicing unit unplug or disconnect electrical supply to the air compressor, bleed tank of pressure, and allow the air compressor to cool.
  • Page 21 PROBLEM CAUSE CORRECTION Pressure reading It is normal for "some" If there is an excessive on the regulated pressure drop to occur. amount of pressure drop pressure gauge when the accessory is used, drops when an adjust the regulator following accessory is the instructions in the used.
  • Page 22 PROBLEM CAUSE CORRECTION Regulator will Damaged regulator. Replace. not shut "Off" air outlet. Motor will not Motor overload protection Let motor cool "Off" run. and overload switch will switch has tripped. automatically reset. Tank pressure exceeds Motor will start automatically when tank pressure drops pressure switch "cut-in"...
  • Page 23 NOTES 23 - ENG A09707...
  • Page 24 GARANTÍA TOTAL DE UN AÑO DEL COMPRESOR DE AIRE Si este compresor de aire Craftsman fallase debido a defectos de materiales o de fabricación dentro del año de su fecha de compra, Sears, a su opción, lo reparará o reemplazará sin costo alguno. Comuníquese con el Centro de Servicio Sears más cercano (1-800-4-MY-HOME) para coordinar su...
  • Page 25: Cuadro De Especificaciones

    CUADRO DE ESPECIFICACIONES Modelo Nº 919.167312 HP de Trabajo Diámetro interior 2,38 pulg. (60,4 mm) Carrera 1,35 pulg. (34,3 mm) Tensión monofásica 120V/60HZ/1PH Circuito mínimo requerido Tipo de fusible Acción retardada Capacidad de aire en el tanque 33 Galones (124,9 litros) Presión de corte de entrada Presión de corte de salida SCFM a 40 psig...
  • Page 26 INSTRUCCIONES IMPORTANTES DE SEGURIDAD GUARDE ESTAS INSTRUCCIONES La operación o el mantenimiento inadecuados de este producto podrían ocasionar serias lesiones y daños a la propiedad. Lea y comprenda todas las advertencias e instrucciones de funcionamiento antes de utilizar este equipo. PELIGRO ADVERTENCIA: Riesgo de Explosión o Incendio qué...
  • Page 27 PELIGRO ADVERTENCIA: Riesgo de Explosión Tanque de aire: las siguientes condiciones podrían, causar el debilitamiento del tanque, y determinar su explosión violenta, daños a la propiedad o serias lesiones. qué puede occurrir cómo prevenirlo Drenaje inadecuado del agua condensada Drene el tanque diariamente o después de en el tanque, siendo la causa del óxido que cada uso.
  • Page 28 PELIGRO ADVERTENCIA: Riesgo de Descarga Eléctrica cómo prevenirlo qué puede occurrir Su compresor de aire está accionado por Jamás opere el compresor a la intemperie electricidad. Como cualquier otro dispositivo cuando está lloviendo o en condiciones de eléctrico impulsado eléctricamente, si no se lo humedad.Nunca opere el compresor sin sus utiliza adecuadamente, podría causarle una defensas o sus cubiertas removidas o...
  • Page 29 PELIGRO ADVERTENCIA: Riesgo de Quemaduras cómo prevenirlo qué puede occurrir Jamás toque partes de metal expuestas en el Tocar el metal expuesto tal como el cabezal compresor durante o inmediatamente después del compresor o los tubos de salida del escape, de la operación.
  • Page 30 PELIGRO ADVERTENCIA: Riesgo de Serias Lesiones o Daños a la Propiedad al Transportar el Compresor (Fuego, inhalación, daño a la superficie de vehículos) cómo prevenirlo qué puede occurrir Deposite el compresor sobre una alfombrilla El aceite puede derramarse y ello podría protectora cuando lo transporte.
  • Page 31: Glosario

    Esta unidad es suficiente para abastecer de energía eléctrica a los siguientes accesorios. Estos se encuentran disponibles a través del catálogo para herramientas eléctricas y manuales, en cualquiera de los comercios que mantiene la línea completa de SEARS. • Lubricadores de niebla de aceite Accesorios •...
  • Page 32: Ensamblado

    ENSAMBLADO Desempaque Extraiga la unidad de su caja y descarte todas las partes de embalaje. INSTALACIÓN CÓMO PREPARAR LA UNIDAD Asegúrese de que el tomacorriente que será utilizado tenga la misma Ubicación del compresor de aire configuración que el enchufe de Ubique al compresor de aire en una zona conexión a tierra.
  • Page 33 Cables de extensión eléctrica Protección del voltaje y del circuito No se recomienda la utilización de cables Acerca del voltaje y la mínima cantidad de circuitos requeridos, refiérase al cuadro de de extensión eléctrica. El uso de cables especificaciones. de extensión eléctrica originará una caída de tensión, lo que determinará...
  • Page 34: Operación

    OPERACIÓN Conozca su compresor de aire LEA ESTE MANUAL DEL PROPIETARIO Y SUS NORMAS DE SEGURIDAD ANTES DE OPERAR LA UNIDAD. Compare las ilustraciones contra su unidad a fin de familiarizarse con la ubicación de los distintos controles y regulaciones. Conserve este manual para referencias futuras.
  • Page 35 Bomba de compresión del aire (no Si el protector de sobrecarga apaga el mostrada): Comprime el aire dentro del motor con mucha frecuencia, verifique si tanque. El aire de trabajo no se encuentra hay algún posible problema de voltaje. disponible hasta que el compresor haya También se puede sospechar de alcanzado a llenar el tanque hasta un nivel bajo voltaje cuando:...
  • Page 36 Cómo poner en marcha: Antes de cada puesta en marcha: Mueva la palanca On/Auto/Off a la Coloque el interruptor On/Auto/Off en posición "On/Auto" y deje que se la posición "Off" y cierre el regulador de incremente la presión del tanque. El aire.
  • Page 37: Mantenimiento

    MANTENIMIENTO Responsabilidades del cliente Antes Cada Diariamente Cada Anualmente o luego de de cada cada uso horas horas Verifique la válvula de seguridad Drenaje del tanque Filtro de aire Válvulas de entrada y escape de la bomba del compresor de aire 1- Más frecuente en condiciones polvorientas o húmedas.
  • Page 38 Extraiga el retén del filtro de aire. Riesgo de Explosión. Dentro del tanque Retire el filtro de aire y asegúrese de se producirá condensación de agua. que esté limpio. Si no drena, el agua lo corroerá y IMPORTANTE: No opere el compresor debilitará...
  • Page 39 SERVICIO Y AJUSTES Todo tipo de mantenimiento y Desenrosque la válvula de retención operaciones de reparación no girándola hacia la izquierda usando mencionados, deberán ser efectuados una llave de boca de 7/8 plug. por personal técnico especializado. (22 mm). Tome nota de la orientación para volverla a Riesgo de ensamblar.
  • Page 40 Ensamble el regulador y oriéntelo de Para reemplazar el regulador acuerdo a lo mostrado. Libere toda la presión del aire del tanque. Vea "Drenaje del tanque" en la sección Mantenimiento. Apagar la unidad colocando el interruptor en On/Auto/Off en "Off". Regulador Usando una llave de tuercas ajustable retire el medidor de salida de presión...
  • Page 41: Almacenaje

    ALMACENAJE Antes de guardar su compresor de aire, Riesgo de asegúrese de hacer lo siguiente: Explosión. El Revise la sección Mantenimiento de agua se condensa dentro del tanque las páginas precedentes y ejecute de aire. Si no se drena, ella corroerá el mantenimiento programado de debilitando la paredes del tanque de acuerdo a la necesidad.
  • Page 42: Guía De Diagnóstico De Problemas

    GUÍA DE DIAGNÓSTICO DE PROBLEMAS Riesgo de Operación Insegura: La unidad arranca automáticamente cuando está enchufada. Al hacer el mantenimiento, el operador puede quedar expuesto a fuentes de corriente y de aire comprimido o a piezas movibles. Antes de intentar hacer reparaciones, desconectar el compresor del tomacorriente, drenar la presión de aire del tanque y esperar a que el compresor se enfríe.
  • Page 43 CORRECCIÓN PROBLEMA CAUSA Si hubiese una caída excesiva Es normal que ocurra algún La lectura de la de presión durante el uso del descenso en la presión. presión sobre un accesorio, ajuste el regulador de manómetro (si acuerdo a las instrucciones de la viene equipado sección Operación.
  • Page 44 PROBLEMA CAUSA CORRECCIÓN El motor no Deje enfriar el motor y el El interruptor de protección des funciona. interruptor de sobrecarga se obrecarga del motor se ha reajustará automáticamente. abierto. El motor arrancará automáticamente La presión del tanque excede cuando la presión del tanque caiga la presión de "corte máximo"...
  • Page 45 NOTES/NOTAS 49 - SP A09707...
  • Page 46: Notes/Notas

    NOTES/NOTAS 50- SP A09707...
  • Page 47: Contratos De Protección Para Reparaciones

    Asistencia telefónica rápida por personal convenient repair scheduling técnico de soporte de Sears para las Once you purchase the Agreement, a unidades que requieran repararse en su simple phone call is all that it takes for you domocilio en horarios convenientes to schedule service.
  • Page 48 Sears Parts and Repair Center. 1-800-488-1222 Anytime, day or night (U.S.A. only) www.sears.com To purchase a protection agreement (U.S.A.) or maintenance agreement (Canada) on a product serviced by Sears: 1-800-827-6655 1-800-361-6665 (U.S.A.) (Canada) Para pedir servicio de reparación Au Canada pour service en français:...

Table of Contents