Advertisement
Forward Collision-Avoidance Assist (FCA)
A
B
(Junction Turning)
Blind-Spot Collision Warning (BCW)*
A
B
(Buttons located on right side of steering wheel)
C
C
D
Rear Cross-Traffic Collision-Avoidance Assist (RCCA)*
Smart Cruise Control (SCC) with Stop and Go System*
A
CRUISE
CRUISE
+
+
RES
RES
OK
OK
CNCL
SET
SET
–
–
(Buttons located on right side of steering wheel)
172ft
130ft
106ft
82ft
REMINDER: Above are approximate distances based
on a 56-mph vehicle speed. The SCC vehicle-to-vehicle
distance increments are based on vehicle speed.
60
Smart Liftgate with Auto Open*
The Smart Liftgate with Auto Open can open the Liftgate automatically when the driver approaches or leaves the vehicle. For Smart
Liftgate with Auto Open to operate, the Smart Key must be positioned in the detecting area (20-39 inches/50-100 cm).
The Smart Liftgate with Auto Open feature is OFF by default. To enable on certain models, go to the User Settings in the Instrument
Cluster LCD modes, then select Door > Smart Liftgate. On other models, press the SETUP key on the infotainment system, followed
by pressing Vehicle > Door > Smart Liftgate on the screen.
Automatically open:
When the Smart Key is on your person and you are near the back of the vehicle, within close proximity, the
hazard lights will blink and a chime will sound for about 3 seconds as an alert that the Smart Liftgate is about to open. Then the
alert system will blink and chime two additional times before opening the Smart Liftgate.
See your Features and Function Guide for more details.
FCA is designed to help alert the driver and, under certain conditions, apply emergency braking
when rapidly approaching a vehicle that is slowing down, braking, or stopped. Initially, the FCA
provides a Forward Collision Warning (FCW) when it detects a potential collision with a vehicle,
pedestrian, or cyclist in front by emitting an audible warning and a visual alert on the Instrument
Cluster
A
. Junction Turning function*
with an oncoming vehicle detected in an adjacent lane when turning left at a crossroad with
the turn signal on. Adjust the alert settings (Standard, Late, Off) in either the Instrument Cluster
or audio settings. FCA is ON by default and can be turned OFF in the Vehicle Settings in the
infotainment system or Instrument Cluster settings menu.
If the system detects that the collision risk has increased, FCA can automatically apply the brakes
to reduce your speed, potentially helping to reduce the effects of a possible collision.
FCA/FCW will become active when the:
• Engine Start/Stop button is ON.
• Vehicle is traveling faster than 5 mph.
• Electronic Stability Control (ESC) is ON.
The BCW system is designed to detect approaching vehicles in the driver's blind spot areas
and warn the driver of a possible collision with a warning indicator and a warning sound. If
there is a collision risk when exiting a parallel space, BCW can assist by applying the brakes
to help avoid a collision.
To enable/disable in User Settings* in the Instrument Cluster — Press the Mode button
the steering wheel and toggle to User Settings. Press the OK button
to Driver Assistance > Driving Safety > Blind-spot Safety.
To enable/disable in Vehicle Settings* in the infotainment system — Press the SETUP key or the
onscreen SETUP button. Press VEHICLE to enter Vehicle Settings. Select Driver Assistance >
Driving Safety > Blind-spot Safety.
Note:
Only adjust settings when the vehicle is at a standstill, gear shift is in PARK, and the
ignition is ON or the Engine Start/Stop button* is in the ON position.
Vehicle detection:
indicator
D
will illuminate on the outside rearview mirrors.
Collision warning:
a flashing indicator
a warning.
Collision-Avoidance Assist* (while departing):
occurred, and the BCW detects a collision risk has increased, BCW can help avoid a collision by
applying the brakes. Your vehicle needs to be traveling less than 2 mph, and the approaching
vehicle is traveling less than 3 mph.
If RCCA detects approaching vehicles from the rear-left or rear-right side of the vehicle, the
system will sound an audible warning, the warning indicators on the outside rearview mirrors
will illuminate, and a message will appear on the LCD Instrument Cluster. RCCA may activate
the Electronic Stability Control to help avoid an imminent collision. RCCA may temporarily apply
braking power when an approaching vehicle is detected within a certain distance next to or
behind the vehicle.
RCCA is designed to operate under the following conditions:
• When the gear shift is in Reverse.
• When your vehicle is moving slower than 6 mph.
The SCC with Stop and Go System is designed to maintain a speed and predetermined distance
from vehicles detected ahead by automatically adjusting the driving speed as needed. When
traffic is detected, the vehicle can slow down to maintain a set distance behind traffic without
depressing the accelerator or brake pedal.
With SCC on and activated, the vehicle-to-vehicle distance set, and when the system detects a
B
vehicle slowing or stopping, the system can bring the vehicle to a complete stop. When the vehicle
ahead starts to move forward, the SCC system re-engages. If the vehicle ahead stops for more than
3 seconds, the accelerator pedal or the RES+ button must be pressed to start moving the vehicle.
D
To set/adjust SCC speed:
• Accelerate/decelerate to the desired speed.
• Press the CRUISE button
will illuminate on the Instrument Cluster.
C
• Press (SET-) button
and vehicle-to-vehicle distance will illuminate on the LCD screen.
• Press (RES+) button
To set the vehicle-to-vehicle distance
image on the LCD screen
To cancel SCC operation:
will display a message that the SCC operation is canceled.
To turn the SCC system OFF:
Instrument Cluster will turn OFF.
E
9
B
may apply emergency braking to help avoid a collision
9
When another vehicle is detected within the BCW warning boundary
When the vehicle detection warning is on and the driver activates a turn signal,
D
will illuminate on the outside rearview mirrors and the system will sound
A
on the steering wheel to turn the system ON. The CRUISE indicator
B
down to set speed. The SET indicator light will illuminate. The set speed
B
up or (SET-) button
:
C
Press the SCC button
E
will change when scrolling through the available distance settings.
Press the CANCEL button
Press the CRUISE button
12
B
If equipped, when a collision warning has already
9
11
B
down to adjust the set speed.
D
on the steering wheel. The
B
or press the brake pedal. The LCD screen
A
. The CRUISE indicator on the
on
A
then toggle up/down
, an
C
Advertisement
