nedis WEST400BK - Weather Station Manual

Table of Contents

Contents

1 Overview of the device
2 Safety
- 2.1 General safety
- 2.2 Battery safety
3 Cleaning and maintenance
4 Documents / Resources
- 4.1 References
- 4.2 Download manual

Overview of the device

1. Mode button	Press the button to set the mode: "AL1" (alarm 1)/ "AL2" (alarm 2) / Normal mode / Time mode. Normal mode: Press the button to switch between "AL1" and "AL2". Press and hold the button to switch between hours and minutes. Press the up/ down buttons to adjust the settings. Press the button to exit. Time mode: Press and hold the button hours, minutes, year, month, day, week and language. Press the up/down buttons to adjust the settings. Press the button to exit.
2. Up button	Press the button to increase the value. Press and hold the button to accelerate the process. Time mode: Press the button to set the temperature display format (°C/°F). Temperature alert mode: Press the button to switch the alarm on or off.
3. Down button	Press the button to decrease the value. Press and hold the button to accelerate the process. Time mode: Press the button to switch between 12H and 24H display. Temperature alert mode: Psress the button to switch the temperature alert on or off.
4. Alarm button	Press the button to switch between the alarm settings "AL1" (alarm 1) on / "AL2" (alarm 2) on / "AL1" + "AL2" on / "AL1" off / "AL2" off.
5. Alert button	Press the button to switch the temperature alert on or off. Press and hold the button for 2 seconds to set the indoor temperature alert. Press the up/down buttons to adjust the settings. Press the button to confirm each setting. Note: For the indoor temperature, the default upper limit is 70°C and the default lower limit is -10°C. Note: If the indoor temperature is outside the set temperature range, a beep will sound 8 times per minute. The temperature and the alert icon will flash. Press any button to stop the temperature alert. The temperature and the alert icon keep flashing and the temperature alert will sound again the next minute.
6. Channel button	Press the button to switch between channels: "CH1" / "CH2" / "CH3" / cycle. After pressing and holding the alert button for 2 seconds, press and hold the button to set the outdoor temperature alert. Press the up/down buttons to adjust the settings. Press the button to confirm each setting. Note: For the outdoor temperature, the default upper limit is 70°C and the default lower limit is -40°C. Note: If the outdoor temperature is outside the set temperature range, a beep will sound 8 times per minute. The temperature and the alert icon will flash. Press any button to stop the temperature alert. The temperature and the alert icon keep flashing and the temperature alert will sound again the next minute.
7. Light button Snooze button	Normal mode: Press the button to set the display brightness: AC adapter: Press the up/down buttons to set the display brightness to high level, medium level or off. Battery: Press the up/down buttons to set the display brightness to high level or medium level. Alarm mode: Press and hold the button to set the snooze interval. If the alarm sounds, press the button to activate the snooze function. Press any other button to stop the alarm. Press the button and subsequently any other button to switch off the snooze function.
• Battery compartment	Open the battery compartment. Insert the batteries (2x AAA) into the battery compartment. Close the battery compartment. Note: After inserting the batteries, the device will detect the indoor temperature and humidity (barometer value) and subsequently the outdoor temperature and humidity for 3 minutes.

Safety

General safety

Read the manual carefully before use. Keep the manual for future reference.
The manufacturer is not liable for consequential damages or for damages to property or persons caused by non-observance of the safety instructions and improper use of the device.
Only use the device for its intended purposes. Do not use the device for other purposes than described in the manual.
Do not use the device if any part is damaged or defective. If the device is damaged or defective, replace the device immediately.

Battery safety

Use only the batteries mentioned in the manual.
Do not use old and new batteries together.
Do not use batteries of different types or brands.
Do not install batteries in reverse polarity.
Do not short-circuit or disassemble the batteries.
Do not expose the batteries to water.
Do not expose the batteries to fire or excessive heat.
Batteries are prone to leakage when fully discharged. To avoid damage to the product, remove the batteries when leaving the product unattended for longer periods of time.
If liquid from the batteries comes into contact with skin or clothing, immediately rinse with fresh water.

Cleaning and maintenance

Do not use cleaning solvents or abrasives.
Do not clean the inside of the device.
Do not attempt to repair the device. If the device does not operate correctly, replace it with a new device.
Do not immerse the device in water or other liquids.
Clean the outside of the device using a soft, damp cloth.

Support
If you need further help or have comments or suggestions please visit www.nedis.com/support