Fcc Notice - Polycom iPower 9000 Product Information

iPower Collaboration Systems Product Regulatory Information
Warning
iPower 9000 and iPower 900 collaboration systems are Class A products. In a domestic environment, these products may
cause radio interference in which case the user may be required to take adequate measures.
USA and Canadian Regulatory Notices

FCC Notice

Class A Digital Device or Peripheral - iPower 9000 or iPower 900
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Class B Digital Device or Peripheral - iPower 600
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modifications
In accordance with Part 15 of the FCC rules, the user is cautioned that any changes or modifications not expressly approved
by Polycom Inc. could void the user's authority to operate this equipment.
Part 68 FCC Rules
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the Telecom Interface
Board of this equipment is a label that contains, among other information, a product identifier in the format
US:AAAEQ#TiPower9000, US:AAAEQ#TiPower900, or US:AAAEQ#TiPower600. If requested, this number must be provided
to the telephone company.
If you experience trouble with your iPower 9000, iPower 900, or iPower 600, for repair or warranty information, please contact
Polycom Inc. at 1-888-248-4143 or 4750 Willow Road, Pleasanton, CA 94588-2708, USA. Contact information may also be
found at http://www.polycom.com/. If the system is causing harm to the network, the telephone company may request that you
disconnect it until the problem is corrected.
If, in the unlikely event that the iPower 9000, iPower 900, or iPower 600 causes harm to the network, the telephone company
will notify you in advance that temporary discontinuance of service may be required. However, if advance notice is not practical,
you will be notified as soon as possible. You will be advised of your right to file a complaint with the FCC if you believe it is
necessary.
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the
operation of your equipment. If they do, you will be given advance notice so that you may make any changes necessary to
maintain uninterrupted service.
WHEN PROGRAMMING EMERGENCY NUMBERS AND/OR MAKING TEST CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to the dispatcher the reason for the call.
2) Perform such activities in the off-peak hours, such as early morning or late evening.
Industry Canada (IC)
iPower 9000 and 900:
This Class [A] digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la Classe [A] est conforme à la norme NMB-003 du Canada.
iPower 600:
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la Classe [B] est conforme à la norme NMB-003 du Canada.
This product meets the applicable Industry Canada technical specifications.
2 www.polycom.com