SAFETY PRECAUTIONS IMPORT ANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service transistors and semicounductor "chip" components. The manual and its supplements and addenda, read and follow the following techniques should be used to help reduce the SAFETY PRECAUTIONS on page 3 of this publication. incidence of component damage caused by static by static NOTE: If unforeseen circumstances create conflict between the electricity.
Page 5
c. Qulckly move the soldering iron tip to the junction of the Fuse and Conventional Resistor component lead and the printed circuit foil, and hold it Removal/Replacement there only until the solder flows onto and around both the 1. Clip each fuse or resistor lead at top of the circuit board component lead and the foil.
SPECIFICATIONS NOTE : Specifications and others are subject to change without notice for improvement. Video input system: Power requirements : Multi 26 System 160-270 Vac, 50/60HZ (Refer to Table 1) Intermediate Frequency Power consumption : Vision IF : 38.0MHz 210 Wmax. Color IF : 33.57MHz [SECAM : 38.0-4.25MHz 34.42MHz(M)
Page 7
T able 1 : Receiving System (26 System) Receiving System Receiving Channel Function P P A A L L - - B B P P A A L L - - G G V V H H F F B B a a n n d d P P A A L L - - I I : : 2 2 - - 1 1 2 2 PAL/SECAM-B...
9 or 4 PLAY sub pictures. P/STILL STOP 5. PSM (Picture Status Memory) recalls your preferred picture setting. 6. SSM (Sound Status Memory) recalls your preferred sound setting. 7. VCR BUTTONS (option) control a LG video cassette recorder. - 8 -...
Page 9
8. DUAL selects the language during dual language broadcast. selects mono sound during stereo broadcasts. POWER MUTE 9. TV/AV I/II selects TV or AV mode. 10. MENU selects a menu. TV/AV 11. ¡ª/¡ (Programme Up/Down) TEXT MENU switches the set on from standby. selects a programme or a menu item.
Page 10
Front panel TV/AV MENU STAND BY PF-60A30 PF-60A30 (L/MONO) (L/MONO) AUDIO AUDIO VIDEO VIDEO S-VIDEO S-VIDEO MAIN POWER <SIDE OF TV> 1. MAIN POWER (on the side of TV) 7. ¡ª/¡ (Programme Up/Down) switches the set on or off. switches the set on from standby.
ADJUSTMENT INSTRUCTIONS Main VCO (Voltage Controlled Oscillator) Safety Precautions Adjustment 1. It is safe to adjust after using insulating transformer between the power supply line and chassis input to prevent Test Point : the risk of electric shock and protect the instrument. 2.
Page 15
RF AGC (Auto Gain Control) Adjustment Cut-off Adjustment Test Point : J104/ J106 NOTE : This adjustment should be performed after warming up for 15 minutes at least. Adjust : VRI1 / VRP1 Test Point : Observing Display The RF AGC control (VRI1/ VRP1 ) was aligned at the time of Adjust : VR902R, 902G, 902B (Cut-off) manufacture for optimum performance over a wide range...
Page 16
RASTER SLANT/POSITION, FOCUS & CONVERGENCE ADJUSTMENT Caution : Lens and Electrical Focus Adjustment These adjustments have been factory aligned. Do not attempt 1. Preliminary steps to temper with these alignments. However, the effects of 1) The electrical focus, the raster slant and position must be adjacent receiver components, or replacement of picture tube provisional alignment.
Page 17
4. Blue lens Adjustment 2) Horizontal Phase Adjustment. Press the volume button and move the convex part 1) Turn the lens until the chromatic aberration changed to the middle of TV screen. purple to green which of 3.5 Cross-Hatch part from picture's center toward left.
Page 18
6. Red Convergence Adjustment 1) Press TV/AV button and select the red cursor. 2) If necessary, cover B lens. 3) Adjust as same as the green convergence adjustment and coincide the red pattern with the green pattern. 7. Blue Convergence Adjustment 1) Press TV/AV button and select the blue cursor.
TROUBLESHOOTING NO PICTURE/ NO COLOR Is the CVBS signal at pin 4 of P101A normal? Check IF Board Is the CVBS signal at Pin 40 of IC201 normal? Check/Replace IC201 Is the Y signal at Pin 3 of IC1D normal? Check/Replace IC1D, Q202 Is the Y signal at Pin 37...
Page 20
NO PIP In case of PIP (AV) In case of PIP (RF) Is there video signal at Is there CVBS signal at pin 29 of IC201? pin 24 of ICP3? Check/Replace IC201 Check Check I C Bus TUNER/IF parts Is there video signal at of PIP pin 26 of ICP3 Check PP2,...
Page 21
NO TELETEXT Check the voltage of CT75(+) Abnormal Normal Abnormal Check the 12V line Check the voltage of CT76(+) to be correct Check/Replace ICT75, PT75 4.8~ 5.2V Check if the video signal inputs at pin 8 of ICT74. Check if the video signal inputs at the pin 40 of IC201.
Page 22
NO PICTURE/NO SOUND (RASTER OK) Does the Auto search operate normal? Is the CVBS signal at Check the voltage Pin 4 of P101A normal? of Tuner (33V, 5V) Check/Replace Check IF Board ZD101, ZD102, R106, R108 GO TO Check pins 20,21, NO PICTURE Block 22,39 of IC1 NO SOUND Block...
Page 23
NO SOUND (PICTURE OK) Check Sound system of station MENU OSD (Manual Programme) BG/I/DK Is the voltage at pin 25 Is the voltage at Pin 25 of IC1 0V(Low)? of IC1 5V(High)? Is the SIF signal at Pin 24 of ICI1 normal? Check/Replace ICI1 Are the Audio signal at Pin...
Page 24
NO RASTER Check +B voltage at R406. Normal Open Is the voltage at Check F801A Pin 3 of IC501 9V? Check 5V, 9V, Check/Replace 12V lines F801A, D821, IC825 Does the square Check the voltage waveform from pin 4 of of C809(+) IC501 appear? Check/Replace...
Page 25
INCORRECT CONVERGENCE Does the static convergence correct? Incorrect Dynamic Incorrect Static Check the input voltage at Readjust static convergence P82PD. by remote controller Normal Abnormal Not controlled Controlled Check pulse pin 125 Check voltage on the Are there pulse signal of IC2051 (4MHz) SMPS PCB at pin 121 of IC2051...
EXPLODED VIEW PARTS LIST The components identified by mark critical for safety. Replace only with part number specified. Part No. Description 4930V00027A HOLDER,METAL SCREEN(A) 4930V00028A HOLDER,METAL SCREEN(B) 3680V00002A LENS,DELTA 79(A-17552-02) R.B 4810V00091F BRACKET,CPT ASSY HOUSING B 4810V00091E BRACKET,CPT ASSY HOUSING G 4810V00091D BRACKET,CPT ASSY HOUSING R 120-C78H...
Replace only with part number specified. LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION IC2054 0IZZVD0005H IC,PF-60A30 D-CON EEPROM ASSY 8PI IC,M35041-078FP 20,SOP BK OSD IC IC2055 0IMI350410M ICP1 0ISA755500A IC,LA7555 24SD PLL VIF+SIF IC2056 0IPH741400E IC,74HC14D 14SOP TP SHITTER TRIGG...
Page 41
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION D807 0DD060009AC DIODE TVR06J 0.6A/600V 250NS ZD502 0DZ510009AB DIODE,ZENER MTZ5.1B,TP(52MM) DIODE TVR06J 0.6A/600V 250NS DIODE ZENER MTZJ7.5B D808 0DD060009AC ZD801 0DZ750009AG D809 0DD060009AC DIODE TVR06J 0.6A/600V 250NS ZD802 0DZ120009AF DIODE,ZENER MTZJ12B D810 0DD060009AC DIODE TVR06J 0.6A/600V 250NS...
Page 42
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 43
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 44
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 45
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film The components identified by mark charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film critical for safety. in the P/No. means as follows; CE : Electrolytic RN : Metal Film Replace only with part number specified.
Page 46
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 47
The components identified by mark critical for safety. Replace only with part number specified. LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION CT92 0CQ1042K439 0.1000UF S 50V J L151 0LA0102K119 INDUCTOR,10UH K 100UF STD 16V M INDUCTOR,10UH K CT94 0CE107DF618 L152...
Page 48
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film The components identified by mark charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film critical for safety. in the P/No. means as follows; CE : Electrolytic RN : Metal Film Replace only with part number specified.
Page 49
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 50
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 51
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film The components identified by mark charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film critical for safety. in the P/No. means as follows; CE : Electrolytic RN : Metal Film Replace only with part number specified.
Page 52
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 54
The components identified by mark critical for safety. Replace only with part number specified. LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION SP101 450-A20B ADAPTER,RF SPLITTER MDZX9-901A T401 6174Z-6079E FBT,FTMPC11-T6079E TU101 113-243B TUNER,TUGG9-A07P(HYPER) TU151 113-243B TUNER,TUGG9-A07P(HYPER) VA801 164-003D VARISTOR,SVC 561D-14A - 54 -...