Dlp projection tv lg ru-44sz51d/ ru-52sz51d (43 pages)
Summary of Contents for LG RT-44SZ80LB
Page 1
website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html LCD Projection TV SERVICE MANUAL CHASSIS : MB-042C MODEL : RT-44/52SZ80LB CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. TV/AV MENU...
SAFETY PRECAUTIONS IMPORT ANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service transistors and semiconductor "chip" components. The manual and its supplements and addenda, read and follow the following techniques should be used to help reduce the SAFETY PRECAUTIONS on page 3 of this publication. incidence of component damage caused by static by static NOTE: If unforeseen circumstances create conflict between the electricity.
Page 5
c. Quickly move the soldering iron tip to the junction of the Fuse and Conventional Resistor component lead and the printed circuit foil, and hold it Removal/Replacement there only until the solder flows onto and around both the 1. Clip each fuse or resistor lead at top of the circuit board component lead and the foil.
CONTROL DESCRIPTIONS All the functions can be controlled with the remote control handset. Some functions can also be adjusted with the buttons on the front panel of the set. Remote control handset POWER Before you use the remote control handset, please install the bat- teries.
Page 7
19. VCR BUTTONS control a LG video cassette recorder. Note : In teletext mode, the PR + / -, SWAP and INPUT buttons are used for teletext function. Battery installation The remote control handset is powered by two AAA type batteries.
Page 8
Front panel Lamp indicator, operation indicator, and temperature indicator, located below the front panel con- trols reveal the operating status of the LCD projection TV. ON/OFF TV/AV MENU TV/AV MENU 1. REMOTE CONTROL SENSOR 7. OPERATION INDICATOR (Refer to p.7) 2.
SPECIFICATIONS NOTE : Specifications and others are subject to change without notice for improvement. Scope This specification can be applied to the LCD Projection(RT-44SZ80LB) Test and Inspection Method 1) performance:Follow the Standard of LG TV test 2) Standards of Extra requirement...
Page 11
Feature and Function Specification Item Remark Unit REMOCON NEC Code analog RGB(separate) RGB Input D-Sub 15 pin digital RGB DVI Input DVI-D RGB Audio(L,R) Input Center Speaker Mode Input L, R Component Audio(L,R) Input Component Input (1 side / 2 rear) AV Input (1 side / 1 rear) S-Video Input...
Page 12
Power Specification Item Remark Unit Power ON/OFF operation 10000 times Normal 220V Staring Voltage Normal 220V Staring Voltage, -10 Degree DC Voltage, Ballast DC Voltage, 5V, stand-by DC Voltage, Digital/ DLP Board 3.3V 3.125 3.465 DC Voltage, Digital/ DLP Board 2.5V 2.375 2.625 DC Voltage, Digital/ DLP Board 5V...
Page 13
Component Video Input (Y, P Specification Proposed Resolution H-freq(kHz) V-freq(Hz) Pixel clock SDTV, DVD 480I 640x480 15.75 59.94 SDTV, DVD 480I 640x480 15.73 59.94 EDTV 480P 31.47 704x480 SDTV, DVD 576I 15.625 720x576 EDRV 576P 720x576 31.250 60.00 HDTV 720P (60Hz) 1280x720 45.00 HDTV 720P (50Hz)
ADJUSTMENT INSTRUCTIONS 1. Application Object 4. LCD adjustment This instruction is for the application to the LCD Projection 4-1. NRS adjustment When the LCD panel load data on regular pixel using high 2. Notes speed change/dischange with sample & holder, the drain (1) The power source insulation of this LCD Projection is not width of TFT gradually decreases and the non-resistance charging type and you may not use the transformer for...
Page 15
Optical measuring equipment Adjustment Connector for RS-232C Adjustment Cable PC Pattern Generator <Fig2-2. TV set status Adjustment> Fig2 Device Configuration Diagram < > (3)Preparation for Adjustment 1) Connect the PC PATTERN GENERATOR, circuit for <Fig3. Adjustment for H/V Position on Screen> adjustment and adjustment JIG as shown <Fig 2>.
Page 16
5) Output the 16 Gray Pattern in PC Pattern Generator. (2) Equipment composition : Follow <Fig2> Check it with the naked eye whether Screen Gamma nad Adjust at same condition of equipment composition diagram. W/B is right about each Gray. If itÕs not, press the ADJ button on Remote Control and (3) Preparation for Adjustment then adjust the level data of each step manually in sub...
Page 17
H Coefficient(KHH, KHL) 17. GL1H : Upper 9bit of MID2 brightness correction --> Calculation method (CEHP-CSHP=1280, Horizontal coefficient in G MIN. segment value =16) --- Change according to GMIN and GMID2 value. 18. GL1L : Lower 9bit of MID2 brightness correction coefficient H coefficient = 1/(number of pixel intervals between setting in the horizontal in G MIN.
Page 18
(4) Adjustment Sequence 2). Input the code(Product Code), production week/year, 1) Adjust the screen coordinates as shown below. Serial number(If it is not input write Ò01Ó) to the S/W for writing DDC. 0 1 2 3 ....xx..15 16 3. Operate EDID Write command. 10.
RT- 44SZ80L P VALID Reset EPLD1 HD- II Dat a[ 0: 7] , [ MUX, VCXO 3- st at e] SDRAM CLK Syn. TP[ 0: 7] , SDRAM IF ( 6M) Slim VSB 27Mhz ATSC/ NTSC ( HY57V643220C) ( LGDPLL) TP_CLK, ( HY57V643220C) SEL_VSB/ 1394,...
Page 20
17. 5 V PW21 15. 5 V 0. 7 inc h LCD Panel ES117 R/ G/ B SIGNAL, Tim ing SAMPLE & R/ G/ B 15. 5 V Pro c essing ( 10b it * 3) HOLDER ( 8b it * 3) LVDS SAMPLE &...
Page 37
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION Q1208 0TR150400BA CHIP 2SA1504S(ASY) KEC DIODE CHIP 2SC3875S(ALY) KEC Q1209 0TR387500AA 0TR150400BA CHIP 2SA1504S(ASY) KEC 0DD226239AA CHIP KDS226 SOT-23 Q1210 Q1211 0TR387500AA CHIP 2SC3875S(ALY) KEC 0DD226239AA CHIP KDS226 SOT-23 Q1213 0TR387500AA CHIP 2SC3875S(ALY) KEC D100...
Page 38
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 39
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 40
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 41
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 42
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 43
R815 0RN5103G409 SW01 140-275E R816 0RN5103G409 510K OHM 1/4 W 1% TA52 140-313B TACTTACT 2LEAD 160G(TA) LG C&D NON R817 0RN5103G409 510K OHM 1/4 W 1% TA52 140-313B TACTTACT 2LEAD 160G(TA) LG C&D NON R818 0RD2202F609 22K OHM 1/6 W 5% TA52 140-313B TACTTACT 2LEAD 160G(TA) LG C&D NON...