To ensure proper installation and operation, take a moment to read this guide before proceeding with the installation. If you have any questions or comments about the MPD ATSC/8VSB/QAM Demodulator, please contact your dealer or have him contact the PICO MACOM Service Center at these phone numbers: 800-421-6511, 818-493-4300.
Page 3
When the product exhibits a distinct change in perfor- mance—this indicates a need for service. CONTACT US 858.546.5050 MPD Owners Manual.indd 3 ATSC/8VSB/QAM Demodulator MPD-CPS Controller/Power Supply 21. Replacement Parts: When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original parts.
Page 4
8VSB or unencrypted QAM digital RF signal and convert it to baseband video and left and right stereo audio outputs. The MPD demodulator can receive all of the 18 ATSC video formats, including HD video, and convert them for display on both analog and digital television sets.
COMM line 1 to module 1, COMM line 2 to module 2, to COMM line 3 to module 3 etc. (fig.3-item 6). 4. Connect the AC power cable to the MPD-CPS (fig. 2-item 11). 5. RF connections: Connect RF input to the MPD (fig.3-item 4).
Page 8
6. An RS232 port (fig.3-item 1) is available for software upgrades. NOTE: Prior to turning on the MPC-CPS verify that all of the modules are properly connected including an OFF-AIR cable to the RF INPUT of each MPD. +5 VDC (4.5A MAX +12 VDC (3.0A MAX...
To enter main menu and to select unit value selected and adjusted RIGHT → To re-enter main menu after unit value has been selected and adjusted BOOT UP UNIT SELECT NOTE: After boot-up sequence is completed the MPD-CPS display will show: CONTACT US 858.546.5050 MPD Owners Manual.indd 9 ATSC/8VSB/QAM Demodulator MPD-CPS...
Page 10
To proceed press ENTER once again. The following screen will appear: REMINDER: Please verify an antenna cable is connected to the input of each MPD prior to scanning. Press the ENTER button to begin channel search or scanning. To stop scanning, press the LEFT ← key once.
Page 11
PICO MACOM After scanning or channel search is completed, the digital channels found are loaded into the CPU of the MPD-CPS. The display will appear as shown: To change or program the module to a different digital channel, do the following: Press ENTER key.
Go to MAIN MENU using the LEFT ← key. Press it one or two times depending on where you are in the Sub Menu. The screen will display: www.picomacom.com MPD Owners Manual.indd 12 figure 14 A T I O figure 15 V O L U >...
Page 13
To select CATV-STD press the ENTER key. To select CATV-HRC press the DOWN ↓ key and press ENTER. To program the unit for additional parameters, follow the procedure previously outlined in similar fashion. CONTACT US 858.546.5050 MPD Owners Manual.indd 13 ATSC/8VSB/QAM Demodulator MPD-CPS figure 18 3 B .
To clean, use a damp cloth only and clean only with mild soap. Do not use solvents or harsh detergents. Do not use this product for purposes other than intended. www.picomacom.com MPD Owners Manual.indd 14 PICO MACOM CONTACT US TOLL FREE 800-421-6511...
Limited Warranty Pico Macom warrants to the original purchaser that all of its new products are of sound design, quality materials and workmanship at the time of manufacture and will be free from related defects for one year from the original purchase date.
Page 18
Restocking fees may otherwise apply beyond this period or if products are not returned in their original condition. Please contact your customer service rep for more information. www.picomacom.com CONTACT US TOLL FREE 800-421-6511 MPD Owners Manual.indd 18 5/8/08 4:51:18 PM...