Removing Packaging Reinforcement - Beko WMB 71242 PTLA Manual

• Total weight of the washing machine and the
dryer -with full load- when they are placed
on top of each other reaches to approx. 180
kilograms. Place the product on a solid and flat
floor that has sufficient load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where
temperature may fall below 0ºC.
• Place the product at least 1 cm away from the
edges of other furniture.

Removing packaging reinforcement

Tilt the machine backwards to remove the
packaging reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
Removing the transportation locks
A
Do not remove the transportation locks before
taking out the packaging reinforcement.
A
Remove the transportation safety bolts before
operating the washing machine, otherwise, the
product will be damaged.
1. Loosen all the bolts with a spanner until they
rotate freely (C).
2. Remove transportation safety bolts by turning
them gently.
3. Attach the plastic covers supplied in the User
Manual bag into the holes on the rear panel. (P)
C
Keep the transportation safety bolts in a safe
place to reuse when the washing machine
needs to be moved again in the future.
C
Never move the product without the
transportation safety bolts properly fixed in
place!
Connecting water supply
C
The water supply pressure required to run
the product is between 1 to 10 bars (0.1 – 10
MPa). It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
C
If you are going to use the double water-inlet
product as a single (cold) water-inlet unit, you
must install the supplied stopper to the hot
water valve before operating the product.
(Applies for the products supplied with a blind
stopper group.)
C
If you want to use both water inlets of the
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
supplied with a blind stopper group.)
A
Models with a single water inlet should not be
connected to the hot water tap. In such a case
the laundry will get damaged or the product will
switch to protection mode and will not operate.
A
Do not use old or used water inlet hoses on
the new product. It may cause stains on your
laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product. Red
hose (left) (max. 90 ºC) is for hot water inlet,
blue hose (right) (max. 25 ºC) is for cold water
inlet.
A
Ensure that the cold and hot water connections
are made correctly when installing the product.
Otherwise, your laundry will come out hot at the
end of the washing process and wear out.
2. Tighten all hose nuts by hand. Never use a
wrench when tightening the nuts.
3. Open the taps completely after making the hose
connection to check for water leaks at the
connection points. If any leaks occur, turn off
the tap and remove the nut. Retighten the nut
carefully after checking the seal. To prevent
water leakages and damages caused by them,
keep the taps closed when the machine is not
in use.
Connecting to the drain
• The end of the drain hose must be directly
connected to the wastewater drain or to the
washbasin.
A
Your house will be flooded if the hose comes
out of its housing during water discharge.
Moreover, there is risk of scalding due to
high washing temperatures! To prevent such
situations and to ensure smooth water intake
and discharge of the machine, fix the end of the
discharge hose tightly so that it cannot come
out.
• The hose should be attached to a height of at
least 40 cm, and 100 cm at most.
• In case the hose is elevated after laying it on the
floor level or close to the ground (less than
40 cm above the ground), water discharge
becomes more difficult and the laundry may
come out excessively wet. Therefore, follow the
heights described in the figure.
3
EN