Related Manuals for Toro TimeCutter 75746
Summary of Contents for Toro TimeCutter 75746
- Page 1 Form No. 3441-554 Rev A 42in TimeCutter ® Riding Mower Model No. 75746—Serial No. 400000000 and Up Model No. 75746TA—Serial No. 400000000 and Up *3441-554* Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Figure 1
Authorized Service model. Dealer or Toro Customer Service and have the model The enclosed engine owner's manual is supplied and serial numbers of your product ready. Figure 1 for information regarding the US Environmental... -
Page 3: Table Of Contents
safety messages that you must follow to avoid Transporting the Machine ......... 24 accidents. This symbol will appear with the word Maintenance ............26 Danger, Warning, or Caution. Maintenance Safety.......... 26 Recommended Maintenance Schedule(s) ... 26 • Danger indicates an imminently hazardous Pre-Maintenance Procedures ...... -
Page 4: Safety
Safety This machine has been designed in accordance with ANSI B71.1-2017. General Safety This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury or death. • Read and understand the contents of this Operator’s Manual before starting the engine. -
Page 5: Slope Indicator
Slope Indicator g011841 Figure 3 You may copy this page for personal use. 1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. -
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1. - Page 7 decal131-1097 131-1097 1. Oil drain decal139-2388 139-2388 3. Fast 1. Slow 2. Hauling decal132-0872 132-0872 1. Thrown object 3. Severing hazard of hand hazard—keep bystanders or foot—keep away from away from the machine. moving parts. 2. Thrown object hazard, 4. Entanglement raised deflector—do not hazard—keep away operate the machine with...
- Page 8 decal139-2394 139-2394 1. Traction controls 4. Neutral 2. Fast 5. Reverse 3. Slow 6. Parking brake decal139-2395 139-2395 1. Parking brake 4. Neutral 2. Fast 5. Reverse 3. Slow 6. Traction controls decal139-2392 139-2392 decal142-5864 142-5864 decal135-3295 135-3295 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal.
-
Page 9: Product Overview
Product Overview g337732 Figure 4 1. Engine 4. Motion-control levers 7. Deflector 10. Control panel 2. Operator seat 5. Rear drive wheel 8. Smart Speed™ lever 3. Fuel-tank cap 6. Front caster wheels 9. Height-of-cut lever... -
Page 10: Controls
Controls Motion-Control Levers Use the motion-control levers to drive the machine Become familiar with all the controls before you start forward, reverse, and turn either direction (Figure the engine and operate the machine. Park Position Control Panel Move the motion-control levers outward from the center to the P position when exiting the machine to engage the electric brake... -
Page 11: Before Operation
Authorized Service Dealer or authorized Toro • Do not allow children or untrained people to distributor or go to www.Toro.com for a list of all operate or service the machine. Local regulations approved attachments and accessories. may restrict the age of the operator. The owner... -
Page 12: Adding Fuel
Fuel Safety compartment to help prevent fires. Clean up oil or fuel spills. • Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Adding Fuel – To prevent a static charge from igniting the fuel, place the container and/or machine directly on Recommended Fuel the ground before filling, not in a vehicle or on... -
Page 13: Performing Daily Maintenance
Understanding the Safety-Interlock System The safety-interlock system is designed to prevent the engine from starting unless: • The blade-control switch (PTO) is disengaged. • The motion-control levers are in the P position. The safety-interlock system also is designed to shut off the engine whenever the control levers are out of the P position and you rise from the seat. -
Page 14: Positioning The Seat
Positioning the Seat Adjusting the Tilt You can adjust the motion-control levers forward or The seat can move forward and backward. Position rearward for your comfort. the seat where you have the best control of the machine and are most comfortable (Figure Loosen the upper bolt holding the control lever to the control-arm shaft. - Page 15 Before using the • Use only accessories and attachments approved machine on a slope, do the following: by Toro. – Review and understand the slope instructions • in the manual and on the machine. This machine produces sound levels in excess of 85 dBA at the operator’s ear and can cause...
- Page 16 – Evaluate the site conditions of the day to determine if the slope is safe for machine operation. Use common sense and good judgment when performing this evaluation. Changes in the terrain, such as moisture, can quickly affect the operation of the machine on a slope.
-
Page 17: Operating The Mower Blade-Control Switch (Pto)
Operating the Mower Operating the Throttle Blade-Control Switch (PTO) You can move the throttle control between the F and S positions (Figure 16). The blade-control switch (PTO) starts and stops the Always use the F position when engaging the PTO. mower blades and any powered attachments. -
Page 18: Starting The Engine
Starting the Engine CAUTION Children or bystanders may be injured if they Note: A warm or hot engine may not require choking. move or attempt to operate the machine while Important: Do not engage the starter for more it is unattended. than 5 seconds at a time. -
Page 19: Driving The Machine
Driving the Machine Driving Backward Move the levers to the center, unlocked position. The drive wheels turn independently, powered by To go backward, slowly pull the motion-control hydraulic motors on each axle. You can turn 1 side levers rearward (Figure 21). -
Page 20: Using The Side Discharge
Using the Side Discharge Disengage the blade-control switch. Adjust the lever to the desired position. The mower has a hinged grass deflector that disperses clippings to the side and down toward the The following are only recommendations for use. turf. Adjustments vary by grass type, moisture content, and the height of the grass. -
Page 21: Adjusting The Height Of Cut
Adjusting the Height of Cut Adjusting the Anti-Scalp Rollers Note: The transport position is the highest height-of-cut position or cutting height at 114 mm Whenever you change the height of cut, adjust the (4-1/2 inches) as shown in Figure height of the anti-scalp rollers. You can adjust the height of cut from 38 to 114 mm Note: Adjust the anti-scalp rollers so that the rollers... -
Page 22: Operating Tips
It is best to cut only about a third of the grass blade. genuine Toro replacement blade. Cutting more than that is not recommended unless grass is sparse, or it is late fall when grass grows more slowly. -
Page 23: After Operation
After Operation Turn the ignition key on and disengage the parking brake by moving 1 motion-control lever out of the P position. After Operation Safety Note: Do not start the machine. General Safety • Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operator’s position. -
Page 24: Transporting The Machine
Transporting the Machine Use a heavy-duty trailer or truck to transport the machine. Use a full-width ramp. Ensure that the trailer or truck has all the necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you or bystanders avoid injury. - Page 25 If using a trailer, connect it to the towing vehicle and connect the safety chains. If applicable, connect the trailer brakes and lights. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees (Figure 26).
-
Page 26: Maintenance
• To ensure optimum performance, use only • Carefully release pressure from components with genuine Toro replacement parts and accessories. stored energy. Replacement parts and accessories made by • Check the parking brake operation frequently. -
Page 27: Pre-Maintenance Procedures
CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders. Shut off the engine and remove the key from the switch before you perform any maintenance. Pre-Maintenance Lubrication Procedures Greasing the Bearings Raising the Machine... -
Page 28: Engine Maintenance
Engine Maintenance Separate the foam and paper elements (Figure 32). Engine Safety • Keep your hands, feet, face, clothing, and other body parts away from the muffler and other hot surfaces. Allow engine components to cool before performing maintenance. • Do not change the engine governor speed or overspeed the engine. -
Page 29: Servicing The Engine Oil
Servicing the Engine Oil Engine-Oil Specifications Oil Type: Detergent oil (including synthetic) of API service SJ or higher Crankcase Capacity: 1.9 L (64 fl oz) with oil filter Viscosity: See the table below. g017552 Figure 33 Checking the Engine-Oil Level Service Interval: Before each use or daily g307458 Note:... - Page 30 g027477 Figure 36 Slowly pour approximately 80% of the specified g225280 Figure 35 oil into the filler tube and slowly add the additional oil to bring it to the Full mark (Figure 37). Change the engine-oil filter (Figure 36). Note: Ensure that the oil-filter gasket touches the engine and then turn the filter an extra 3/4 turn.
-
Page 31: Servicing The Spark Plug
g027478 Figure 38 Checking the Spark Plug Important: Do not clean the spark plug(s). Always replace the spark plug(s) when it has a black coating, worn electrodes, an oily film, or cracks. If you see light brown or gray on the insulator, the engine is operating properly. -
Page 32: Cleaning The Blower Housing
Cleaning the Blower Fuel System Housing Maintenance Service Interval: Every 100 hours/Yearly (whichever DANGER comes first) In certain conditions, fuel is extremely To ensure proper cooling, ensure that the grass flammable and highly explosive. A fire or screen, cooling fins, and other external surfaces of the explosion from fuel can burn you and others engine are kept clean at all times. -
Page 33: Electrical System Maintenance
Electrical System Maintenance Electrical System Safety • Disconnect the battery before repairing the g305646 machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last. • Charge the battery in an open, well-ventilated area, away from sparks and flames. - Page 34 Charging the Battery WARNING Incorrectly removing the cables from Service Interval: Before storage—Charge the battery and disconnect the battery cables. battery could damage the machine and cables, causing sparks. Sparks can Remove the battery from the chassis; refer to cause the battery gasses to explode, Removing the Battery (page 33).
-
Page 35: Servicing The Fuses
Servicing the Fuses Drive System Maintenance The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or short. Checking the Tire Pressure Fuse type: • Main—F1 (25 A, blade-type) Service Interval: Every 25 hours—Check tire pressure. -
Page 36: Adjusting The Tracking
g294417 Figure 46 1. Brake-link arm on the electric brake control module 2. Left, rear tire Adjusting the Tracking When driving the machine forward full speed across a flat, level surface, if the machine pulls to 1 side, adjust the tracking. If the machine pulls to the left, adjust the right motion-control lever;... -
Page 37: Belt Maintenance
Route the new belt around the engine pulley and 48). mower pulleys (Figure 49). Using a spring-removal tool (Toro Part No. 92-5771), install the idler spring over the deck hook and place tension on the idler pulley and the mower belt (Figure 49). -
Page 38: Mower Maintenance
Mower Maintenance Blade Safety • Inspect the blades periodically for wear or damage. • Use care when checking the blades. Wrap the blades or wear gloves, and use caution when servicing the blades. Only replace or sharpen the g006530 blades; never straighten or weld them. Figure 50 •... - Page 39 g014973 g014973 Figure 52 Figure 54 1. Blade (in position for measuring) 1. Opposite blade edge (in position for measuring) 2. Level surface 2. Level surface 3. Measured distance between blade and the surface (A) 3. Second measured distance between blade and surface (B) Rotate the same blade 180 degrees so that If the difference between A and B is greater the opposing cutting edge is now in the same...
-
Page 40: Leveling The Mower Deck
Installing the Blades Install the blade onto the spindle shaft (Figure 55). Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. Install the curved washer (cupped side toward the blade) and the blade bolt (Figure 55). - Page 41 g294044 g294046 Figure 58 Figure 59 1. Blades side to side 3. Measure from the tip of the 1. Blades front to rear 3. Measure from the tip of the blade to the flat surface blade to the flat surface here.
- Page 42 g294195 Figure 62 Install the washer and hairpin cotter (Figure 61). g308865 Figure 60 Repeat steps through for the other side of the machine. 1. Wood block—6.6 cm 2. Wood block—7.3 cm (2-5/8 inches) thick (2-7/8 inches) thick Check the side-to-side level again; repeat this procedure until the measurements are correct.
-
Page 43: Removing The Mower Deck
To lower the front of the mower, loosen the On 1 side of the machine, remove the washer adjustment nut. and hairpin cotter from the deck pin (Figure 65). After adjustment, check the front-to-rear slope again, continue adjusting the nut until the front blade tip is 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip;... -
Page 44: Replacing The Grass Deflector
Repeat steps for the other side of the Place the spring on the rod, with end wires machine. down, and between the grass deflector brackets. Attach the front support rod to the mower deck Slide the rod through the second grass-deflector with the clevis pin and hairpin cotter (Figure 64). -
Page 45: Cleaning
Cleaning Disengage the blade-control switch, shut off the engine, remove the key, and wait for all moving parts to stop. Washing the Underside of Turn the water off and remove the coupling from the washout fitting. the Mower Deck Note: If the mower is not clean after 1 washing, Service Interval: After each use—Clean the soak it and let it stand for 30 minutes. -
Page 46: Storage
Storage Check the condition of the blades; refer to Servicing the Cutting Blades (page 38). Prepare the machine for storage for over Storage Safety 30 days as follows: • Shut off the engine, remove the key, and wait Add fuel stabilizer/conditioner to fresh fuel for all moving parts to stop before you leave the in the tank. -
Page 47: Storing The Battery
Storing the Battery Fully charge the battery. Let the battery rest for 24 hours, then check the battery voltage. Note: If the battery voltage is below 12.6 V, repeat steps and 2. Disconnect the cables from the battery. Check the voltage periodically to ensure that the voltage is 12.4 V or higher. -
Page 48: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The fuel tank is showing signs of collapsing 1. The air-cleaner paper element clogged. 1. Clean the paper element. or the machine is frequently showing signs of running out of fuel. The engine overheats. 1. - Page 49 Problem Possible Cause Corrective Action The machine does not drive. 1. The bypass valves are open. 1. Close the tow valves. 2. The traction belts are worn, loose, or 2. Contact an Authorized Service Dealer. broken. 3. The traction belts are off the pulleys. 3.
-
Page 50: Schematics
Schematics g307974 Electrical Diagram 139-2356 (Rev. A) - Page 51 Notes:...
- Page 52 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.