English
•
The accessories
15
,
14
the extension tube
7
or to the vacuum inlet
in Fig. L.
•
Align the top of the accessories
vacuum inlet
5
or extension tube
it locks into position as shown in Fig. L.
MAINTENANCE
WARNING:
personal injury, turn unit off and remove battery
pack before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Cleaning and Emptying the Vacuum
WARNING:
never use the vac without its filter.
iMPORTAnT: Maximum dust collection will only be obtained
with clean filters and an empty dust canister. If dust begins to
fall back out of the product after it is switched off, this indicates
that the dust canister is full and requires emptying.
nOTE: The filter is re-usable do not throw it away when the
product is emptied. We recommend that you replace the filters
29
,
28
every 6–9 months depending on frequency of use.
To Empty the Dust Canister and Remove the Pre-
filter (Fig. M–P)
1. Lift and remove the lift away dust canister
chassis
24
as shown in Fig. M.
2. While over top of a trash can, grip the recessed tabs
pre-filter
26
and pull upwards to remove the pre-filter with
cyclones and dust canister cap
3. Empty the contents of the dust canister
4. Tap the pre-filter
26
as necessary to remove any debris.
Inserting Pre-filter (Fig. O)
nOTE: The filter housing fits snuggly in the dust canister and
may be difficult to remove at first.
1. Install the pre-filter
26
the dust canister tab
27
shown in Fig. O.
2. Install the dust canister onto the chassis
firmly into position.
Removing filters (Fig. M–P)
1. Lift and remove the lift away dust canister
chassis
24
as shown in Fig. M.
2. Unscrew the dust canister cap
the dust canister
10
.
3. Remove the foam filter
the plastic loop
30
.
Cleaning the filters
1. Once the filters and pre-filter are removed from the dust
canister
10
shake off or lightly brush any loose dust from
the pre-filter
26
and foam filter
8
,
13
can be fitted either directly to
5
as shown
15
,
14
,
13
with the
7
and push into place so
To reduce the risk of serious
Projectile/Respiratory Hazard:
10
from the
9
.
10
.
into the dust canister
10
ensuring
aligns with the recessed tabs
24
, until it clicks
10
from the
9
anticlockwise and lift off
29
and felt filter
28
by pulling on
29
and felt filter
28
2. Rinse out the dust canister
3. Wash the foam filter
soapy water.
4. Ensure the foam filter
dry before refitting the filters into the dust canister cap
5. Once the filters
them inside the dust canister cap
side in the upwards position.
nOTE: The black foam
into the dust canister cap from the underside.
6. With the filters
cap
9
clockwise onto the pre-filter
7. The pre-filter
dust canister
Pre-Filter section.
iMPORTAnT:
•
Wash the filters regularly using warm, soapy water and
-
ensure that it is completely dry before using again. The
cleaner the filter is, the better the product will perform.
-
It is very important that the filters are completely dry
and correctly in position before use.
Removing and Cleaning the Rotary Brushes
(Fig. Q)
WARNING:
moving parts, disconnect the floor head and extension tube
from the vacuum before cleaning or servicing.
1. To remove the rotary brush
the release latch
25
of the
2. With the rotary brush
grab and lift the rotary brush
floorhead
3. Wipe away any dust or debris on the rotary brush
4. Reinstall the rotary brush
aligning the keyed end of the rotary brush
located in the floorhead
5. Align the squared end of the rotary brush
square slot on the floorhead
25
as
6. Press firmly on the rotary brush
floorhead
release latch
Replacement Filter
The filter should be replaced every 6 to 9 months and whenever
worn or damaged. Replacement filters are available from your
BLACK+DECKER service centre.
Visit www.2helpu.com to locate a service centre.
Cleaning
WARNING:
maintenance on cordless appliance remove the battery.
.
10
with warm soapy water.
29
and felt filter
29
and felt filter
29
,
28
are clean and completely dry, place
9
29
side will be visible when looking
,
fitted, screw the dust canister
29
28
26
can now be inserted into the lift away
10
according to instructions in the inserting
To reduce the risk of injury from
31
from the floorhead
32
towards the rear of the floorhead
31
released from the floorhead
31
completely out of the
11
to clean.
31
into the floorhead
11
.
11
.
31
to secure it into the
11
. Ensure you hear an audible click as the
32
snaps into its locked position.
Before performing any
28
with warm
28
are completely
9
.
with the white felt
28
26
.
11
slide
11
.
11
,
31
.
11
by
31
with the gear
31
with the