Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for LG WD-12270FD
Summary of Contents for LG WD-12270FD
- Page 1 Website: http: //www.LGEservice.com E-mail: http: //www.LGEservice.com/techsup.html WASHING MACHINE SERVICE MANUAL CAUTION READ THIS MANUAL CAREFULLY TO DIAGNOSE PROBLEMS CORRECTLY BEFORE SERVICING THE UNIT. MODEL: WD(M)-12270(5)BD / WD-12270(5)FD...
- Page 2 FEB. 2004 PRINTED IN KOREA P/No.:3828ER3027E...
-
Page 3: Table Of Contents
CONTENTS 1. SPECIFICATIONS .........................3 2. FEATURES & TECHNICAL EXPLANATION ................4 3. PARTS IDENTIFICATION ......................7 4. INSTALLATION & TEST ....................... 8 5. WIRING DIAGRAM/PROGRAM CHART ..................11 6. OPERATION ..........................12 7. TROUBLESHOOTING.........................14 7-1. BEFORE PERFORMING SERVICE ...................14 7-2. QC TEST MODE.........................14 7-3. -
Page 4: Specifications
1. SPECIFICATIONS ITEM WD(M)-12270(5)BD, WD-12270(5)FD COLOR BLUE WHITE POWER SUPPLY AC 220-240V~, 50Hz PRODUCT WEIGHT 86 kg WASHING 200 W ELECTRIC POWER DRAIN MOTOR 37 W CONSUMTION WASH HEATER 2200 W WASH 42 rpm REVOLUTION SPEED SPIN 1200 rpm CYCLES WASH/RINSE TEMPERATURES SPIN SPEEDS OPTIONS... -
Page 5: Features & Technical Explanation
2. FEATURES & TECHNICAL EXPLANATION 2-1. FEATURES Direct Drive System The advanced Brushless DC motor directly drives the drum without belt and pulley. Tilted Drum and Extra Large Door Opening The tilted drum and extra large door opening make it possible to load and unload easily. - Page 6 2-2. NEURO FUZZY WASHING TIME OPTIMIZATION To get the best washing performance, optimal time is determined by the water temperature, the selected washing temperature, and the size of the load. water temperature washing time the best selected NEURO- washing washing rinsing time temperature FUZZY...
- Page 7 2-5. THE DOOR CAN NOT BE OPENED While program is operating When a power failed and power plug is taken out in operation While Door Lock lights turn on. White the motor is in the process of intertial rotating, through the operation is paused. 2-6.
-
Page 8: Parts Identification
3. PARTS IDENTIFICATION ACCESSORIES... -
Page 9: Installation & Test
4. INSTALLATION & TEST Before servicing, ask the customer what the trouble is. Check the setup (power supply is 220-240V AC, remove the transit bolts..). Check with the troubleshooting guide. Plan your service method by referring to the disassembly instructions. Service the unit. - Page 10 HOW TO CONNECT THE INLET HOSE Verify that the rubber washer is inside of the valve connector. Tighten the inlet hose securely to prevent leaks. CONNECT THE DRAIN HOSE Make sure that the hose is not twisted. Avoid submerging the end of the hose. The end of the drain hose should be placed less than 100 cm from the floor.
- Page 11 TEST OPERATION Preparation for Press the POWER button. Press the START/PAUSE washing. button. Connect the power plug to Listen for a click to determine if the outlet. the door has locked. Connect the inlet hoses. Check the water heating Check the automatic Check the water supply.
-
Page 12: Wiring Diagram/Program Chart
5. WIRING DIAGRAM PROGRAM CHART 3 2 1 3 2 1 3 2 1 3 2 1 2:19 1:22 1:04 1:01 Duvet 1:21... -
Page 13: Operation
6. OPERATION • Use this button to turn the power • This display shows: On/Off. a) the estimated time remaining in the cycle when operating. b) an error code when an error has been detected. Wool/Silk Delicate Hand Wash Synthetic Quick 30 Cotton-Eco Duvet... - Page 14 TIME DELAY • These lights show which portion of the • Allows the start of any cycle cycle the washer is operating. to be delayed for 3~19 hours. Pre Wash Wash Rinse Spin Time Delay Processing Child Lock Time Delay Time Save Time Save •...
-
Page 15: Troubleshooting
7. TROUBLESHOOTING 7-1. BEFORE PERFORMING SERVICE Be careful of electric shock when disconnecting parts while troubleshooting. The voltage of each terminal is 220-240V AC and DC when the unit is plugged in. 7-2. QC TEST MODE. The washer must be empty and the controls must be in the off state. 1. -
Page 16: Error Display
7-4. ERROR DISPLAY If you press the START/PAUSE button when an error is displayed, any error except will disappear and the machine will go into the pause status. In case of if the error is not resolved within 20 sec., or the in case of other errors, if the error is not resolved within 4 min., power will be turned off automatically and the error code will blink. - Page 17 ERROR SYMPTOM CAUSE OVER • MAIN PWB ASSEMBLY is out of order. CURRENT • Winding in the STATOR ASSEMBLY is short-circuited. ERROR • The connector (3-pin, male, white) in the MOTOR HARNESS is not connected to the connector (3-pin, female, white) of STATOR ASSEMBLY. •...
-
Page 18: Error Diagnosis And Check List
8. ERROR DIAGNOSIS AND CHECK LIST 8-1. DIAGNOSIS AND SOLUTION FOR ABNORMAL OPERATION SYMPTOM GUIDE FOR SERVICE CALL No power Is the power plug connected firmly to 220-240V AC outlet? Power failure? or Breaker opened? Is the outlet controlled by a switch? Visit to service. - Page 19 SYMPTOM GUIDE FOR SERVICE CALL Door error Was the load too large? Visit to service. Drain trouble Visit to service.
- Page 20 SYMPTOM GUIDE FOR SERVICE CALL Suds overflow from the Is a low-sudsing detergent used? appliance. (In this condition, wash and spin do not operate normally) LOW-SUDSING Is the proper amount of detergent used as recommended? Recommend to reduce the amount of detergent.
-
Page 21: Fault Diagnosis And Troubleshooting
8-2. FAULT DIAGNOSIS AND TROUBLESHOOTING CAUTION 1. Be careful of electric shock if disconnecting parts while troubleshooting. 2. First of all, check the connection of each electrical terminal with the wiring diagram. 3. If you replace the MAIN PWB ASSEMBLY, reinsert the connectors correctly. NO POWER Check the fuse or reset Is the supplied voltage 220-240V AC? - Page 22 VIBRATION & NOISE IN SPIN Have all the transit bolts and base packing Remove the transit bolts been removed? and Base packing. Is the washer installed on a solidly constructed Move the washer or floor? reinforce the floor. Check if the washer is perfectly level as follows: Base Packing Level Check the leveling of the washer with a Level...
- Page 23 If it still has severe vibration and noise, regulate a specific spin speed that generates excessive vibration and noise as follows: 1) Put an unbalance part (rubber) inside of the drum. 2) Start the QC test mode (Refer to section 7-2). 3) Press Delay Wash button, then ‘...
- Page 24 NO WATER SUPPLY Is water supply shut-off? Is the tap opened? Open the tap. When you press both SPIN button and RINSE Check the AIR CHAMBER button simultaneously, is the water level frequency and the tube (clogged). below 246? Is the inlet valve filter clogged? Clean the filter.
- Page 25 LIQUID DETERGENT/SOFTENER DOES NOT FLOW IN Refer to Is water supplied? NO WATER SUPPLY Check the wiring on the Are the plugs correctly connected to the terminals of dispenser. the INLET VALVE ASSEMBLY? Put it in the correct Is liquid detergent/softener/bleach put in the correct compartment.
- Page 26 HEATING WITHOUT WATER When pressing SPIN and RINSE at the same time after draining, is the water level frequency 255? Replace the When pressing SPIN and RINSE buttons at the same SENSOR SWITCH Rinse Spin time while washing, is the water level frequency ASSEMBLY.
- Page 27 WASH HEATER TROUBLE 220-240V AC 220-240V HEATING CONTINUOUSLY ABOVE THE SETTING WATER TEMPERATURE Temp. button Temp. Push the THERMISTOR When checking the THERMISTOR on the tub, tightly to the rubber. is the THERMISTOR loose?
- Page 28 WILL NOT CIRCULATE WATER Is the impeller of the drain pump clogged? Remove foreign material. Hose Connector Hose (White) Remove foreign material. Are the Hose Connector and/or Hose clogged? Reconnect or repair Is the connector disconnected, disassembled? the connector. Connector Connector Is the coil of the right side of drain pump open Replace PUMP MOTOR...
- Page 29 SPIN TROUBLE Check the SENSOR SWITCH Check during spin if the frequency of the water ASSEMBLY or HOSE (Pressure). level is 248 or more. If the problem is on the SENSOR SWITCH ASSEMBLY or the Rinse Spin HOSE, replace the SENSOR SWITCH ASSEMBLY or the HOSE.
-
Page 30: Disassembly Instructions
9. DISASSEMBLY INSTRUCTIONS Be sure to unplug the machine out of the outlet before disassembling and repairing the parts. CONTROL PANEL ASSEMBLY TOP PLATE ASSEMBLY Unscrew 2 screws on the back of the top plate. Pull the top plate backward and upward as shown. Disconnect the Display PWB Assembly connector from Trans cable. - Page 31 MAIN PWB ASSEMBLY Disconnect the POWER connector and SENSOR SWITCH ASSEMBLY. Remove the Protect Cover. CONNECTOR PROTECT COVER Disconnect the connectors. Unscrew 1 screw on the back. Disassemble the Main PWB.
- Page 32 DISPENSER ASSEMBLY Disassemble the top plate assembly. Pull out the drawer. Push out the DISPENSER ASSEMBLY after unscrew 2 screws. Unscrew the nut at the lower part of the dispenser. Disassemble the 2 or 3 connectors from the valves. Wire Color Blue Housing (BK-GR/WH) White Housing (BK-WH/BK) Red Housing (BK-BL/RD)
- Page 33 REACTOR Unscrew the a screw from the Top Bracket. Disassembly one connector from the Main PWB. CABINET COVER Unscrew the 4 screws from upper of the canbinet cover. Unscrew the screw from filter cover. Put a flat ( - ) screwdriver or putty knife into the both sides of the filter cover, and pull it out.
- Page 34 Open the door. Disassemble the clamp assembly. Tilt the cabinet cover. Disconnect the door switch connector. NOTE: When assembling the CABINET COVER, connect the connector. Lift and separate the cabinet cover. Disassemble the clamp assembly. Disassemble the Gasket.
- Page 35 DOOR Open the door. Unscrew the 7 screws from the HINGE COVER. Put a flat ( - ) screwdriver into the openng of the hinge, and pull out the hinge cover. Unscrew a screw from the lower side of door. Disassemble the door upward.
- Page 36 Disassemble the cabinet cover. Separate the pump hose, the bellows and the circulation hose assembly from the pump assembly. Disassemble the pump assembly in arrow direction. Disassemble the cabinet cover. Separate 2 connectors from the heater. Loosen the nut and pull out the heater. CAUTION •...
- Page 37 Disassemble the cabinet cover. Separate the heater from the tub. Remove any foreign objects (wire, coin, etc.) by inserting a long bar in the opening. Unscrew the 4 screws from the back cover. Unscrew the single screw from the lower-right side of the cabinet.
- Page 38 Disassemble the back cover. Remove the bolt. Pull out the Rotor. Unscrew the 2 screws from the tub bracket. Remove the 6 bolts on the stator. Unplug the 2 connectors from the stator. Disassemble the damper hinges from the tub and base.
-
Page 39: Exploded View
10. EXPLODED VIEW 10-1. CABINET & CONTROL PANEL ASSEMBLY F215 A480 A485 F210 F110 A450 A455 A104 A105 A102 A103 A111 A110 A410 A490 A150 A154 A495 A152 A101 A141 A151 A153 A100 A131 A130 A430 A140 A133 A440 A155 A300 A310 A201... -
Page 40: Drum & Tub Assembly
10-2.DRUM & TUB ASSEMBLY K351 K350 K360 K143 K123 F140 K610 K411 K410 K611 K115 F466 K110 K141 K111 K140 F315 K572 F310 K571 F465 K570 F463 K122 F464 K125 K130 K320 K530 K310 K121 K510 K311 K512 K560 K105 K135 K131 K340... -
Page 41: Dispenser Assembly
10-3.DISPENSER ASSEMBLY F324 F322 F462 F321 F300 F170 F160 F226 F225 F436 F430 F220 F431 F441 F440 F435 F120 HOT (RED) A275 F130 COLD (BLUE) A276 A273 A274 F432 A271 A272 A270...