Metabo SSW 18 LTX 1450 BL Instructions Manual page 11

For SSW 18 LTX 400/1450/1750 BL / SE the speed
and the tightening torque can be set on the
thumbwheel (6) (12 stages).
Recommendation: determine the correct
setting by carrying out trial screwdriving.
SSW 18 LTX 1450/1750 BL additionally
have the function of AutoPowerShift (APS)
for the controlled removal of screws. The machine
runs at full speed when the screw is loosened and
reduces the speed as soon as the screw is
loosened.
6.5 Change screwdriving bit for SSW ...
Inserting screwdriving bit: Fit the tool on the
square attachment (1) until the limit stop.
Removing screwdriving bit: Pull the tool from the
square attachment (1).
The screwdriving bit used must match the
screw.
Damaged screwdriving bits must not be used.
7. Use
Mount the machine on the screw, ensuring it is
aligned straight.
The screwdriving process consists of 2 parts: insert
screw and
tighten screw with the impact mechanism.
The tightening torque depends on the impact
duration.
With an impact duration of approx. 5 seconds, the
maximum tightening torque has been reached.
The torque curve depends on the type of
application:
With a hard screwdriving application (screw-
couplings in hard material such as metal), maximum
tightening torque is already reached after a short
impact duration (a).
With a soft screwdriving application (screw-
couplings in soft material such as wood), a longer
impact duration (b) is required.
Recommendation: determine the correct impact
duration by carrying out trial screwdriving.
Caution! For small screws the maximum torque
can be reached already after
0.5 seconds impact duration.
- This is why the duration of the screwdriving
process must be monitored exactly.
- Adjust the tightening torque by pressing firmly or
lightly on the trigger (3), ensuring that the screw is
not damaged or that the screw head does not tear
off.
Eyelet for fall protection
-The eyelet (12) is designed for attaching a
suitable, original Metabo tool fall protection
securing lanyard. Check the eyelet for damage
prior to each use. Read and follow the operating
instructions of the tool securing lanyard! After
each fall, have the machine checked for damage
by a trained specialist and repaired if necessary.
8. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
See page 4.
A Chargers:
B Battery packs with different capacities
Use only battery packs with voltage suitable for
your power tool.
C Screwdriving bits
D Tool 1/2" / 3/4"
For a complete range of accessories, see
www.metabo.com or the catalogue.
9. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
10. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).
ENGLISH en
11