Advertisement
Quick Links
IMPORTANT NOTICE!!
Read the enclosed instructions carefully before attempting to install this door. Pay close
attention to all warnings and important safety notices.
This manual MUST be attached to the wall in close proximity of the door.
DS-350 COMMERCIAL ROLL-UP DOORS
WINDLOAD RATED
INSTALLATION INSTRUCTIONS
©Copyright 2002 Wayne-Dalton
P/N 291341, DOC #101-0093-1 REV 03
Advertisement
Related Manuals for Wayne-Dalton DS-350
Summary of Contents for Wayne-Dalton DS-350
- Page 1 DS-350 COMMERCIAL ROLL-UP DOORS WINDLOAD RATED INSTALLATION INSTRUCTIONS IMPORTANT NOTICE!! Read the enclosed instructions carefully before attempting to install this door. Pay close attention to all warnings and important safety notices. This manual MUST be attached to the wall in close proximity of the door.
-
Page 2: Important Safety Notices
IMPORTANT SAFETY NOTICES Read the enclosed instructions carefully before attempting installation. If there are any questions about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs. 1. Operate the door ONLY when it is properly adjusted and free of all obstructions. 2. - Page 3 Reference must be made to construction codes in your area. All Wayne-Dalton DS-350 Windload Rated Commercial Roll-Up Doors follow the general instructions contained herein. Additional installation information for the specific door shipped is found with the packing slip and on supplementary drawings.
-
Page 4: Operation
You will be told later when to do this. No guarantee will be given by Wayne-Dalton if the door is not erected as instructed. For best operation, follow the instructions step by step. Please review all instructions thoroughly before starting installation. - Page 5 STEP 3 INSTALLING MOUNTING ANGLES, GUIDES, AND BOTTOM BAR STOPS Obtain the appropriate Bolt Line (BL) measurement from the chart below. Use Opening Width listed on packing slip. Any variation between the actual opening width and the width listed on the packing slip is to be ignored. OPENING WIDTH ANGLE FACE TO ANGLE FACE (STEEL)
- Page 6 Align the guide slots with the slots in the wall angles and fasten guides with the interior windlock return towards the door jamb using the 5/16-18 x 5/8” truss head bolts, washers, and flange nuts. Slide guides to set the “H” dimension as shown above at 1- 3/4”...
- Page 7 After installing the brackets and drive components, install the axle tensioner devices. On the non-operator side of the curtain slide the tensioner device on the axle and ensure the arrow pointing to the wall on the device will point to the wall when the door is installed. Next, slide the tensioner support device on the opposite side of the axle, again making sure t hat the arrow on the device points to the...
- Page 8 until bottom bar angle easily clears sto ps. If the door has a tendency to close, secure in position using clam ps. If the door has a tendency to rise, secure in position using a wood prop. While the door is secured from m oving, tighten the bottom bar stop fasteners on both guide assem blies...
- Page 9 TEP 10 CHECK AND ADJUST SPRING BAL ANCE Lower and raise the door to check the counterbalance. If the door lowers easily and raises hard, more spring tension is required. If the door lowers hard and raises easily, less spring tension is required. First, open the door fully and sten vise grips to guides below bottom bar.
- Page 10 REDUCED DRIVE CHAIN HOIST INSTALLATION INSTRUCTIONS (if applicable) STEP 11 ALIGN THE SPROCKETS Feed the hand chain through the pocket wheel assembly (installed in step #4), around the cast iron hand chain wheel, and connect the two end links. Align the chain hoist so that the 41B9 sprocket on the pocket wheel assembly is in line with the 41A40 sprocket bolted to the barrel.
- Page 11 Roll-Up Sheet Door LIMITED WARRANTY Wayne-Dalton P.O. Box 67- Mt. Hope, Ohio 44660 The Manufacturer warrants the ROLL-UP SHEET DOOR and hardware fittings for a period of ONE YEAR from the time of delivery against any defects in workmanship or material. Manufacturer shall, upon notification, correct such nonconformity at its option, by repairing or replacing any defective part or parts.