Rotary broom 48 with polypropylene brush for craftsman tractors (72 pages)
Summary of Contents for Sears CRAFTSMAN C 151 61681 1
Page 1
MANUAL MODEL NO. C 151 61681 1 48" UTILITY BLADE FOR Caution: CRAFTSMAN TRACTORS Read and Follow All Safety Rules and Instructions Before Operating This Equipment ·Assembly ·Operation ·Maintenance ·Repair Parts Sears Canada, Inc., Toronto, Ontario M5B 2B8 104675 H-04...
Page 2
LIMITED ONE (1) YEAR WARRANTY ON CRAFTSMAN TRACTOR ATTACHMENTS "UTILITY BLADE" For one (1) year from date of purchase, Sears Canada Inc. will repair or replace free of charge at Sears option any parts which are defective as a result of defective material or faulty workmanship.
INTRODUCTION TO THE PURCHASER This new accessory was carefully designed to give years of dependable service. This manual has been provided to assist in the safe operation and servicing of your accessory. NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or accessory, but are intended for reference only and are based on the latest product information available at the time of publication.
SAFETY PRECAUTIONS Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. All operators, no matter how experienced they may be, should read this and other manuals related to the vehicle and accessory before operating.
Page 6
SAFETY PRECAUTIONS 13.Never operate the accessory without good visibility OPERATION: or light. 1. Do not put hands or feet near, under or inside rotating parts. 14.Keep the accessory away from heat sources or flames. 2. Exercise extreme caution when operating on or crossing gravel drives, walks or roads.
ASSEMBLY IMPORTANT: TORQUE ALL BOLTS ACCORDING TO TORQUE SPECIFICATION TABLE (SEE TABLE CONTENTS) WHEN STATED: TIGHTEN FIRMLY. REFER PARTS BREAKDOWN SECTION FOR PARTS IDENTIFICATION. NOTE: This subframe was designed to fit various models of tractors. Make sure to follow the instructions that correspond to your tractor.
ASSEMBLY STEP 2 SUBFRAME INSTALLATION: You must choose which brace pin (item 1 or item 4) that is appropriate for your tractor model. Tractors with a clutch that measures 5.5” high only (as shown): You must use brace pin (item 1) and install it in the bottom holes of the right support (item 2) with two carriage bolts 3/8’’...
Page 10
ASSEMBLY RIGHT SUPPORT: Install the right support (item 1) on the right side. The chart identifies the hardware according to the holes in the tractor’s frame. Even though some holes may not exist on certain models of tractors, use the maximum of holes &...
Page 11
ASSEMBLY LEFT SUPPORT AND HANDLE SUPPORT: Install the left support (item 1) and the handle support (item 17). Secure the brace pin (item 19) The chart identifies the hardware according to the holes in the tractor’s frame. Even though some holes may not exist on certain models of tractors, use the maximum of holes &...
Page 12
ASSEMBLY If necessary, slide the shim (item 20, previous page) between the tractor frame and the support, in line with hole (item 9 or item 11). (Make sure that the shim stays perpendicular with the top of the support). Slightly tighten the screws and bolts. Make sure that the brace pin stays straight and does not come into contact with any part of the tractor (ex: the engine belt when mower deck is in raised posi-...
Page 13
ASSEMBLY TRACTORS WITH MANUAL CLUTCH ACTIVATED BY A CABLE: If it is not possible to put back in place the tractor’s belt guides, use the replacement belt guides supplied. Insert the collars (item 1) on the brace pin (item 4). Tighten slightly.
Page 14
ASSEMBLY ASSEMBLY PIVOT SUPPORT: Turn the front wheels towards the right. Install the pivot support (item 1) between the two supports and slide in place the pin (item 2) in the required holes. The other holes get the hooked end (item 5) of the pin.
Page 15
ASSEMBLY LIFT MECHANISM: Slide the link (item 1) inside the box of the right support (item 2). Insert the pin (item 3) inside the link. Insert the lift arm (item 4) on the pin (item 5) of the right support and on the pin (item 3). Secure the arm with one washer (item 6) and one hair pin 4 mm (item 7).
ASSEMBLY STEP 3 UTILITY BLADE PREPARATION: Install the push frame (item 1) to the attaching frame (item 2) with a 5/8 x 3 1/2’’ hex bolt (item 3) and a nylon insert lock nut (item 4). Do not tighten too much so that the push frame moves freely.
ASSEMBLY STEP 4 UTILITY BLADE INSTALLATION: WARNING TO PREVENT INJURIES: Stop the motor. Apply parking brake. Remove the ignition key. Attach the utility blade to the subframe as shown. Make sure the blade is pushed in until locked into place by the springs (item 1). Attach the blade Install the plastic handgrip (item 5) on the handle (item 1).
OPERATION RAISING OR LOWERING THE UTILITY BLADE: The manual lift arm for raising and lowering the utility blade is located on the right hand side of the tractor. To WARNING raise the blade, pull back on the lift arm. To lower the blade, push the lift arm slowly towards the front.
MAINTENANCE & DISMOUNTING BEFORE DOING ANY MANTENCE OR END OF SEASON STORAGE: DISMOUNTING AN ACCESSORY, REFER TO THE SAFTEY PRECAUTIONS. a) Clean and repaint all parts from which the paint has worn off. MAINTENANCE: b) Inspect and replace all defective parts before using next season.
PARTS BREAKDOWN / NOMENCLATURE DES PIÈCES UTILITY BLADE / LAME UTILITAIRE...
Page 21
PARTS LIST / LISTE DES PIÈCES Ref. English description Description française Qty. Part # Réf. Qté. Pièce # 1 Blade Lame 102856 2 Cutting edge 48" Racloir 48" 102854 3 Carriage bolt 5/16" n.c. x 3/4" Boulon à carrosserie 5/16" n.c. x 3/4" STD533107 4 Flange nut 5/16"...
PARTS BREAKDOWN / NOMENCLATURE DES PIÈCES SUBFRAME / SOUS-CHÂSSIS...
Page 23
PARTS LIST / LISTE DES PIÈCES Ref. English description Description française Qty. Part # Réf. Qté. Pièce # 1 Right support Support droit 104332 2 Lift arm Bras de relevage 104336 3 Left support Support gauche 104331 4 Brace pin Tige de renfort 104334 5 Link...
Page 24
PARTS LIST / LISTE DES PIÈCES Ref. English description Description française Qty. Part # Réf. Qté. Pièce # 39 Carriage bolt 3/8" n.c. x 3/4" Boulon à carrosserie 3/8" n.c. x 3/4" STD533707 40 Belt guide Guide courroie 104348 41 Collar Collet 104349 42 Machine screw P.H.#10 x 24 x 3/4"...
TORQUE SPECIFICATION TABLE GENERAL TORQUE SPECIFICATION TABLE USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal oil. They do not apply if special graphited or moly disulphide greases or other extreme pressure lubricants are used. This applies to both UNF and UNC threads.
ATTACHMENTS & OPTIONS ROTARY BROOM 48" /#700381 with polypropylene brush. COUNTERWEIGHT UTILITY BLADE #61913 Fits on same subframe as #700266 Required for safety and traction. snowblower & utility blade Mounts on the same subframe as the Counter-balances weight of Requires adaptor #700379 snowblower &...
_______________________________________________________________________________________________ Pour service en francais: 1-800-LE-FOYER (1-800-533-6937) www.sears.ca ®/TM Trademarks of Sears, Roebuck and Co. used under license by Sears Canada ® Marque deposée/ Marque de commerce de Sears, Roebuck and Co. utilisée en vertu d’une licence de Sears Canada...