Summary of Contents for Sinclair TURBO STRIPPER II
- Page 1 £ TURBO STRIPPER II Operating Manual Read before use and keep safe Rev A Starting With Turbo II Ser# 193-07 06/21/07 (800) 624-2408 (530) 626-9386 Fax (530) 626-5144 6686 Merchandise Way Diamond Springs, Ca 95619 www.sineqco.com...
-
Page 2: Table Of Contents
Table of Contents Technical Data Page 3 Safety Page 3 Assembly & Handle Adjustment Page 6 Maintenance Page 7 Page 8 Information About Various Floorings Page 11 Trouble Shooting Page 11 Spare Parts/Schematics Page 15 Blade Selection Page 18... -
Page 3: Technical Data
Turbo£ Stripper, 2 rigid blades, safety goggles and tool kit. 2.0 Safety The Sinclair Turbo£ Stripper is state of the art designed and meets all standard safety requirements. 3.1 Safety Instructions Disconnect the power supply before any maintenance is carried out. - Page 4 Transport Always remove the blade before transporting the machine. Disconnect the power supply and the plug of the clutch before removing the handle. Otherwise you might damage the hydraulics of the clutch. Mount the steel plate (1) instead of the clutch. Turn thumb screw (3) clockwise until the drive wheels are locked.
-
Page 5: Use
Sinclair Equipment Company cannot be held responsible for the performance of or any damage arising from the use of machines in which genuine spare parts have not been used. - Page 6 3.0 Assembly of Machine & Handle Insert handle into Turbo II base as shown in diagram. Tighten wing bolts in handle. Note that bolts are spring loaded to get past foot pad. Position both bolts facing up as shown in diagram. 3.1 Adjustement Of Handle To adjust handle, loosen wing bolt on back of handle.
- Page 7 4.0 Maintenance The Turbo£ Stripper is virtually maintenance free. The guide shaft castings require lubrication from time to time. (after approx. 1650 sq. feet). Initially the machine is fully lubricated and should not require any additional lubrication for the first 5000 square feet. The grease fittings are located on each side.
- Page 8 Changing the blade Disconnect the power supply and put on the blade protection before changing the blade. Use work gloves for your own safety. - release bar on side of handle & tip the machine as shown put on the blade protection (enclosed in the tool set) Warning! Very sharp blade! You may cause injury without using the blade protection!
- Page 9 The Turbo£ Stripper is equipped with a Power -on indicator lamp (1) and an operating Switch located at the top of the handle. The switch has a restart protection for low-voltage failures. If the lamp does not indicate power-on, use another power socket or check power supply.
- Page 10 Assembly of support for additional weight (accessory) The weight of the Turbo Stripper is expandable by 1 up to 3 additional weights (each weight is 66 lbs) Sinclair part# T38535 Individual weight shifting is possible at 3 positions (see picture).
-
Page 11: Information About Various Floorings
Emergency running The Turbo Stripper can be operated also with broken or damaged hand clutch as follows: - Disconnect power supply - Insert emergency-run-unit in place of clutch. - Screw-in thumb-screw (3) until the driving wheels are blocked - If the emergency-run-plate is mounted, the motor drive is always switched on. - Page 12 7.1 Repairing the Hydraulic System To repair the hydraulic system, use the Sinclair Hydraulic Clutch Repair Kit, which can be ordered through your local distributor. Hydraulic Clutch Repair Kit This kit contains all hydraulic fittings, compression washers, tubing, fluid, and specific tools necessary to completely rebuild the Turbo£...
- Page 13 Filling and Bleeding The System Turn the clutch adjustment screw #2 (2mm Allen screw, located in the handle behind the lever of the master cylinder #7) counterclockwise as far as it will go. Insert the straight barbed adapter into the top end of the clear tubing and insert the tip of the syringe into the bottom end of the tube.
- Page 14 Turbo Hydraulic Clutch Parts 1. Hydraulic Tubing – T099998T (Order qty 42) 2. Master Cylinder with Lever. (#2)- T0730236 3. Screw for Clamp – T0999996 4. Clamp – T0999995 5. Lever Blade W Plunger & Lock – T0999994 6. Slave Cylinder – T0321830 7.
-
Page 15: Spare Parts/Schematics
Spare Parts/Schematics Schematic # Description Part# Chassis T015106 Piston block T015054 Screw M 8x30 T014736 Washer, M8 D014860 Lubricating nipple T014914 Cover T038534 Screw M 8x25 T014735 Additional Weight T038535 Screw M10x80 T039234 Screw Nut T039189 Bushing 20x26x20 T014909 Blade holder Turbo / Jaw T038536 Striking foot Turbo T015127... - Page 16 Circlip I 62 T014856 Circlip A 17 T014850 Ball bearing 6305 T014712 Circlip A 30 T014853 Excenter shaft Turbo T015145 Nut key 4x4x20 T014901 Key 6x6x25 T014903 Circlip A 25 T014852 Bearing block right or left T017079 Screw M 10x70 T014742 Cyl.
- Page 17 Hydraulic-clutch assy T038837 Transport Axle T042739 Strain relief T017559 Handle T014917 Cyl. Screw, micro M6 x 20 D014752 Bracket for Lifting Strap T015107 Cyl. Screw, M8 x 16 T017651 Washer T017452 Indicator T038638 Cyl. Screw, M6 x 60 T018259 Fitting T038585 Elastic Stop Nut M8 T014816...
- Page 20 If you have any questions on blade selection or choice of machine, please do not hesitate to call Sinclair Equipment Company or your...
- Page 21 Not responsible for lost job or down time. In no event shall SINCLAIR be liable for any indirect, incidental, or consequential damages from the sale or use of the product. This disclaimer applies both during and after the term of this warranty.
- Page 22 Notes...