Table of Contents
Advertisement
- release trigger switch to stop the tool
- put button in the right position to prevent accidently
switching on the tool
Changing saw blades 8
•
! remove battery from tool before making any
adjustments or changing accessories
! insert blade to full depth with teeth facing forward
9
- tool accepts most commonly available T-shank and
U-shank blades 8
•
Sawing at 45° q
•
Selecting sawing mode w
Use lever for adjusting the orbital action from accurate
cutting (= 0) to fast cutting (= 3)
- 1 setting ("0") for accurate cutting in all materials,
straight + curved
- 3 settings for fast cutting in different materials, straight
cuts only
1 = aluminum, plastic
2 = hard wood
3 = soft wood
! always select "0" when sawing splinter-sensitive
material
•
LED-worklight
- The LED worklight will automatically turn on with a
slight squeeze on the trigger switch before the tool
starts running, and will turn off 8 to 12 seconds after the
trigger is released.
- When the tool and/or battery pack becomes
overloaded or too hot, the internal sensors will turn the
tool off. If the tool and/or battery pack are overloaded,
the LED worklight will rapidly flash. Rest the tool for
a while or place the tool and battery pack separately
under air flow to cool.
- The LED worklight will flash more slowly to indicate that
the battery pack is at low-battery capacity. Recharge
the battery pack.
•
Switch for dust blowing r
•
Dust suction t
- connect vacuum cleaner adaptor to foot
- connect vacuum cleaner hose to vacuum cleaner
adaptor
•
Operating the tool
- before switching on the tool, ensure that front end of
footplate rests flat on the workpiece
- hold tool firmly with both hands, so you will have full
control of the tool at all times
! while working, always hold the tool at the grey-
coloured grip area(s) y
- ensure that complete surface of footplate rests firmly on
the workpiece
! ensure that the blade has come to a complete
standstill, before you lift the tool from the
workpiece
- keep ventilation slots uncovered
•
Battery protection
Switches off the tool or prevents the tool from being
switched on, when
- the load is too high
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C
- the lithium-ion battery is nearly empty (to protect
against deep discharge)
All manuals and user guides at all-guides.com
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
APPLICATION ADVICE
•
Use the appropriate saw blades u
! tool accepts most commonly available T-shank
and U-shank blades 8
•
When cutting metals, lubricate saw blade regularly with
oil
•
For an accurate straight cut, guide tool with footplate
along the edge of a straight piece of wood i
•
Pre-drill a hole before making cut-outs o
•
Splinter-free cutting
- cover cutting-line with several layers of wide tape
before cutting
- always face the good side of the workpiece down
MAINTENANCE
•
This tool is not intended for professional use
•
Always keep tool clean (especially ventilation slots)
! remove battery from tool before cleaning
•
If lever loosens during use, set the tightness of lever p
- place lever in middle position
- loosen lock screw with PH2 screw driver counter
clockwise
- tighten set screw finger tight with Allen key 4mm
counter clockwise
! set screw uses left hand thread
- tighten lock screw with PH2 screw driver clockwise
- tighten lever
ENVIRONMENT
•
Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 4 will remind you of this when the need for
disposing occurs
11
Advertisement
Table of Contents
