Related Manuals for Texas Instruments TPA4411
Summary of Contents for Texas Instruments TPA4411
- Page 1 TPA4411 Audio Power Amplifier Evaluation Module User’s Guide August 2004 Mixed-Signal Products SLOU172...
- Page 2 TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:...
- Page 3 EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety measures typically found in the end product incorporating the goods.
- Page 4 EVM schematic located in the EVM User’s Guide. When placing measurement probes near these devices during operation, please be aware that these devices may be very warm to the touch. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2004, Texas Instruments Incorporated...
- Page 5 SLOU011) provides detailed information on the evaluation platform and its use with TI audio evaluation modules. TPA4411 80-mW Capless Stereo Headphone Amplifier (literature number SLOS430) This is the data sheet for the TPA4411 audio amplifier integrated circuit. Trademark NanoFreet is a trademark of Texas Instruments Incorporated.
- Page 6 FCC Warning FCC Warning This equipment is intended for use in a laboratory test environment only. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference.
-
Page 7: Table Of Contents
Contents Contents Introduction ..............Description . - Page 8 Contents viii...
-
Page 9: Introduction
Chapter 1 Introduction This chapter provides an overview of the Texas Instruments (TI) TPA4411 capless stereo headphone amplifier evaluation module. It includes a brief description of the module and a list of EVM specifications. Topic Page Description ........... -
Page 10: Description
Description 1.1 Description The TPA4411 is a capless stereo headphone amplifier capable of delivering 80 mW/Ch without the added output DC blocking capacitors. The TPA4411 EVM includes connections for input, power, ground, pushbuttons, and a head- phone jack for the outputs. -
Page 11: Operation
Chapter 2 Operation This chapter describes how to operate the TPA4411EVM. Topic Page Quick Start for Stand Alone Operation ......Operation... -
Page 12: Quick Start For Stand Alone Operation
This means that a low voltage (ground) on this pin will place the appropriate channel in shutdown mode. Using the pushbuttons provided on the EVM, the TPA4411 can be placed in shutdown by pressing and holding the button(s) down. Both buttons must be depressed in order for both channels of the TPA4411 to turn off. -
Page 13: Reference
Chapter 3 Reference This chapter includes the EVM schematic, parts list, and board layout reference. Topic Page TPA4411EVM Schematic ........TPA4411EVM Bill of Materials . -
Page 14: Tpa4411Evm Schematic
Figure 3−1. TPA4411EVM Schematic C6 10 µF R1 121 kΩ (optional) C3 2.2 µF R2 121 kΩ C4 2.2 µF C1 1 µF IN_R C2 1 µF PGND IN_L TPA4411 NC12 OUTR PVSS OUT_R (test point) C5 2.2 µF OUT_L... -
Page 15: Tpa4411Evm Bill Of Materials
0603 Panasonic ERJ−3EKF1213J Panasonic, SDL, SDR Momentary switch P8048SCT−ND Texas Instruments, TPA4411 audio amplifier IC 4 × 4 thin QFN package TPA4411RTJ Kycon, Inc., P/N Headphone jack ST−3000 2 Position, 2 mm header (not installed) Sullins, PTC36SABN SAMTEC Terminal post headers Headers TSW−19−8−G−S... -
Page 16: Tpa4411Evm Pcb Layers
TPA4411EVM PCB Layers 3.3 TPA4411EVM PCB Layers Figure 3−2. Top Layer Figure 3−3. Bottom Layer...