Page 1
SYSTEM AIR CONDITIONER SINGLE for North America (R-410A, Heat Pump) INDOOR UNIT OUTDOOR UNIT AR36BSHUMGMNCV AR36BSHUMGMXCV AIR CONDITIONER CONTENTS 1. Precautions 2. Product Speci cations 3. Disassembly and Reassembly 4. Troubleshooting 5. PCB Diagram and Parts List 6. Wiring Diagram...
Contents 1. Precautions ........................1-1 1-1. Precautions for the Service ..........................1-1 1-2. Precautions for the Static Electricity and PL ....................1-1 1-3. Precautions for the Safety ..........................1-1 1-4. Precautions for Handling Refrigerant for Air Conditioner ................1-2 1-5. Precautions for Welding the Air Conditioner Pipe ..................1-2 1-6.
Page 3
Contents 5. PCB Diagram and Parts List ..................5-1 5-1. Indoor Unit Main PBA ............................5-1 5-2. Indoor Unit Sub PBA ............................5-3 5-3. Outdoor Unit Main PBA ..........................5-4 5-4. Outdoor Unit inverter PBA ..........................5-6 5-5. Outdoor Unit EMI PBA ............................. 5-7 6.
Explain to workers that the battery for the remote control needs to be separated for storage purposes when the product will not be used for a long time. – This can cause a problem for the remote control since battery fluid may trickle out. Samsung Electronics...
If the Wall Mounted type(Wind free) indoor unit is included in the installation combination, please contact us before changing the Capacity correction for heating function to 33kg/cm2g during Outdoor unit key function setting. Samsung Electronics...
Page 10
PANEL FRONT. (use + Screw Driver) 4) Loosen connector wire(white) and detach the temperature sensor wire. 5) To detach the FRONT-PANELthe main frame, unfasten 2 screw at the bottom. (use + Screw Driver ) 6) Take off the FRONT-PANEL,lifting up the bottom Samsung Electronics...
Page 11
3) To detach TRAY-DRAIN from the main frame , pull the bottom of the TRAY- DRAIN towards you. CONTROL IN 1) Unfasten the earth screw. (use + ScrewDriver) 2) Detach the temperature sensor and Humidity sensor. 3) Detach the temperature sensor. Samsung Electronics...
Page 12
(use + Screw Driver) 1) Loosen the STEP UP/DOWN connector (CN802). tion When you separate the connector, pull pressing the locking button. 2) Loosen the FUSE CHK connector (CN140). When you separate the connector, pull pressing the locking button. Samsung Electronics...
Page 13
5) Loosen the DISPLAY connector. (CN501). The terminal is locking type. So, when you separate terminals, pull pressing the button. 6) Loosen the POWER connector. When you separate the connector, pull pressing the locking button. Samsung Electronics...
Page 14
9) Take off the main PBA from the ASS’Y Control in. When you take off the PBA, don’t touch the components. Please hold the PBA both side. EVAPORATOR 1) Unfasten the screw at the right side. (use + ScrewDriver) Samsung Electronics...
Page 16
3) unfasten the screw a little and pull the MOTOR FAN to the right side. (use + Screw Driver) 4) Loosen 1 fixing screws of HOLDER-FAN. (use + Screw Driver) 5) unfasten the screw a little. (use + Screw Driver) Samsung Electronics...
Page 17
1) Remove the 9 screws which is fixed to each side of Cabinet Upper and separate it.(Use + Screw Driver) Cabinet-Installation 1) Remove the 1 screw which is fixed to Front Part Cabinet-Installation Front Part and separate it.(Use + Screw Driver) Samsung Electronics...
Page 18
Cabinet Rear RH 1) Pull out the sensor from the Cabinet Rear RH and separate it. 2) Remove the 4 screws which is fixed to each side of Cabinet Rear RH and separate it. (Use + Screw Driver) 3-10 Samsung Electronics...
Page 19
Cabinet-Installation 1) Remove the 1 screw from the Rear Part Cabinet-Installation Rear Part and separate it.(Use +Screw Driver) Cabinet Front LF 1) Remove the 9 screws from the Cabinet Front LF and separate it. (Use +Screw Driver) Samsung Electronics 3-11...
Page 20
Disassembly and Reassembly Parts Procedure Remark Cabinet Front LF 1) Remove the 2 fixing nuts like the pic- ture on the right side. (Use Hexagon Wrench, Monkey Spanner, Hexagon Socket) 3-12 Samsung Electronics...
Page 21
2) Remove the 8 screws which is fixed to Motor. (Use +Screw Driver) 3) Separate the Motor Wire connector from the Outdoor Unit Control Part. Bracket Motor 1) Remove the 2 screws from the Bracket Motor and separate it. (Use +Screw Driver) Samsung Electronics 3-13...
Page 22
Disassembly and Reassembly Parts Procedure Remark Control Part 1) Separate the 4 connectors from the Outdoor Unit Control part. 2) Remove the 2 screws which is fixed to Control Part. (Use +Screw Driver) 3) Separate the Control Part. 3-14 Samsung Electronics...
Page 23
Compressor and then separate the Pipe by welding torch. EEV Valve 1) Remove the 2 screws which is fixed to Service Valve and separate it. (Use +Screw Driver) 2) Separate the inlet and outlet pipes by welding torch Samsung Electronics 3-15...
Page 24
Cover and separate it. (Use Hexagon Wrench, Monkey Spanner, Hexagon Socket) 2) Separate the Felt Compressor. 3) Remove the 3 bolts from the bottom of Compressor like the picture on the right side. (Use Hexagon Wrench, Monkey Spanner, Hexagon Socket) 3-16 Samsung Electronics...
Mode button High Fan button High Temp button Low Temp button Low Fan button Entering mode for option setting. Step 1 Option setting procedure. (The option setting procedure is the same for other models.) Step 2 Samsung Electronics...
Press Mode button to be changed to AUTO mode in the OFF status. 11. Setting SEG14, SEG15 option Press Low Fan button( ) to enter SEG14 value. Press High Fan button( ) to enter SEG15 value. Each time you press the button, … will be selected in rotation. SEG14 SEG15 Samsung Electronics...
Page 27
Press Mode button to be change to HEAT mode in the OFF status. 19. Setting SEG23, SEG24 mode Press Low Fan button( ) to enter SEG23 value. Press High Fan button( ) to enter SEG24 value. Each time you press the button, … will be selected in rotation. SEG23 SEG24 Samsung Electronics...
Page 28
Troubleshooting Check the option you have set Input option Step 4 Check operation Step 5 Samsung Electronics...
1. If you want to use the various additional functions for your Wired Remote Controller, press the set and delete buttons at the same time for more than three seconds. 2. Refer to the list of additional functions for your Wired Remote Controller on the next page, and select the desired menu. Samsung Electronics...
Troubleshooting 4-4-14. Compressor starting error / rotation error (Error Code : E461, E467) Check the power connection. Check the restart after power reset. Check the compressor and connection of compressor wires. Samsung Electronics 4-27...
Troubleshooting 4-4-15. Full current error / PFC over-current error (Error Code : E462, E484) operation at restart. End the service. End the service. Samsung Electronics 4-29...
4-4-16. IPM (Over Current) error (Error Code : E464) Outdoor unit installation and environment check. Check for normal operation at restart. End the service. Check installation environment of indoor unit. check for normal operation at restart. End the service. 4-30 Samsung Electronics...
Reference Sheet 7. Reference Sheet 7-1. Index for Model Name 7-1-1. Indoor Unit 용량 Type 제품군 출시년도 Feature Design Series Color code Product type 거래선 (K BTU) (Ref, Inv. ONOFF) Samsung Electronics...
You can open the valve by turning the need valve counterclockwise using hex wrench, and it is used for vacuum, gas purging, refrigerant injection, refrigerant purging, and indoor-outdoor unit connection. ACCUMULATOR Accumulator prevents the flow of liquid-state refrigerant into the compressor. (Liquid-state refrigerant flowing into the compressor will overload the compressor.) Samsung Electronics...