Advertisement
OPTION SETTING
[After replacing the Memory IC (IC803)]
The memory IC, IC803, stores the option data and service adjustments for each circuit, therefore, when the memory
IC is replaced, it will need to be re-set to the initial conditions specified below
To enter to the Option Mode
+ Press and hold the F/OK button on the remote control and P
window will appear on the screen.
ON-TIMER
PLUG AND PLAY
WELCOME TEXT
BBE
AUTO VOLUME
HEADPHONE
CRT 16:9 MODE
NOISE REDUCTION
COUNTRY
RASTER ROTATION
SESA
DIGITAL RC
LIGHT MONITORING
OPTION MODE FOR CE15LC3-B-00
To set the option mode
+ Highlight the desired option item by using the P
+ To switch the option mode, use the Volume - (LEFT) or Volume + (RIGHT) button.
+ The data which is set in the option mode is stored into the memory IC automatically.
Following table shows the available option items and initial conditions.
Option Mode
Mode
ON-TIMER
ON or OFF
PLUG AND PLAY
ON or OFF
WELCOME TEXT
ON or OFF
BBE
ON or OFF
AUTO VOLUME
OFF or ON
HEADPHONE
ON or OFF
CRT 16:9 MODE
ON or OFF
NOISE REDUCTION ON or OFF
COUNTRY
EU, UK,
IRE, UK+IRE
RASTER ROTATION ON or OFF
SESA
ON or OFF
DIGITAL RC
ON or OFF
LIGHT MONITORING ON or OFF
Exit from the Service Mode
+ Press the MENU
button.
SERVICE ADJUSTMENTS
Note: Some items of the service adjustments for this chassis are controlled by the CPU, IC801, and the
adjustments are carried out by using the RC handset.
INITIALISATION OF MEMORY IC
To initialise the memory IC (IC803), press and hold the NORMAL
P
button on the TV set and then turn the Mains switch Off and On. The initialisation is now completed.
When initialised the memory IC and all of the setting data (option data and service adjustment data) stored in the IC
are reset to the default value. It is necessary to set the option settings and readjust the service adjustments listed on
page 6 and to re-tune all the channels.
The available adjustment items are as follows;
TDA9885 : This can be adjusted for AGC.
Video
: This can be adjusted for the service adjustment.
DO NOT ADJUST OTHER SETTINGS
[After replacing the Memory IC (IC803)]
The memory IC, IC803, stores the service adjustments data for each circuit, therefore, when the memory IC is
replaced, it should be programmed by using "OPTION SETTING" on previous page and the following adjustments.
TO ENTER SERVICE ADJUSTMENTS
P
on the cabinet front.
The service menu appears.
Service
VGA 20 VER 090
Video
Sound
STV2310
TDA9885
STV8206
Median Filter ON
Other
Colour Temperature
WSS
LCD Parameters
Fan control
Use the 6or 5 to highlight the service menu you require and press the F/OK button to enter.
TO EXIT SERVICE ADJUSTMENTS
Press the Menu button to navigate backwards through the service menus until menus disappear.
IMPORTANT NOTICE
Do not attempt to adjust service adjustments not listed on the above otherwise it may cause
loss of performance and product safety.
PART NO SKP20451
N2GJ PAGE 5/5
button on the front panel of the TV. The option
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
UK
OFF
OFF
OFF
OFF
or P
button .
Description & Note
On-timer available, default "OFF"
Plug and Play mode, default "ON"
Display message when first set up, default "ON"
BBE sound mode, default "OFF"
Default "OFF"
Headphone control , default "OFF"
Default "OFF"
Default "ON"
TV system, default "UK"
Default "OFF"
Default "OFF"
Digital option, default "OFF"
Ambient light control of LCD brightness,default "OFF"
button on the remote control, then press the
While pressing the green button on the remote control press the
Service menu: Video
Enter the service adjustment menu as described on the previous page and select "Video" using
the P
or P
buttons and then press the F/OK button to enter.
Use the P
VIDEO
the F/OK button on the remote control to enter.
G2 Alignment
Config
White Point R
0
White Point G
0
White Point B
0
Peak White Limiter
0
Black Level Offset R
0
Black Level Offset G
0
Gain pre-scale RGB
0
Fast blanking delay
0
Luma/Chroma delay
0
Restore default
Service menu: Sound
Enter the service adjustment menu as described on the previous page and select "Sound" using
the
or
buttons and then press the F/OK button to enter.
P
P
Audio Menu
Audio Type
3
Volume
0
Balance
6
Loudness
13
Spatial effect
0
Service menu: TDA9885
Enter the service adjustment menu as described on the previous page and select "TDA9885"
using the P
or P
buttons and then press the F/OK button to enter
TDA9885
Write 1
70
ADJUSTMENTS
IMPORTANT NOTICE
Do not attempt to adjust the following service adjustments except when adjustments are required in servicing
otherwise it may cause loss of performance and product safety.
AGC ADJUSTMENT
1. Select the clearest VHF station
2. Connect a digital voltmeter to test point TP-A and GND
3. Enter service menu : TDA9885
4. With the P
or P
buttons select "Write 1"
5. Adjust using the
or
buttons until the read-
out from the voltmeter is 3.2 Vdc.
GREY SCALE ADJUSTMENT
SCREEN ADJUSTMENT
1. Make sure the set is warm (20 mins)
2. Receive Black and White picture/pattern
3. Enter service menu "Colour temperature"
4. Select item "Red / Green / Blue"
5. Using the
or
buttons adjust to make the
white, white.
HORIZONTAL ADJUSTMENT
HORIZONTAL CENTRING ADJUSTMENT
1. Set wide screen mode to "FULL".
2. Preferably receive a circular pattern
3. Enter service menu "LCD Parameters"
4. Use the P
or P
buttons to highlight "H Display
start".
5. Press the
or
buttons to adjust horizontal
centre.
VERTICAL ADJUSTMENT
VERTICAL CENTRING ADJUSTMENT
1. Set wide screen mode to "FULL".
2. Preferably receive a circular pattern
3. Enter service menu "LCD Parameters"
4. Use the P
or P
buttons to highlight "V Display start"
5. Press the
or
buttons to adjust the
vertical centre.
or P
buttons to select the option, then press
Use the P
or P
buttons to select the option, then
press the F/OK button on the remote control to enter.
Use the P
or P
buttons to select the option,
then press the F/OK button on the remote
control to enter.
Advertisement
