Panasonic WV-CP240 Operating Instructions

Color CCTV Cameras
Operating Instructions
WV-CP240
Model No.
WV-CP242
WV-CP244
(Lens Option)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N0301-3043 V8QA5733DN
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
CAUTION
These limits are designed to provide reasonable
protection against harmful interference when the
RISK OF ELECTRIC
equipment is operated in a commercial environ-
SHOCK DO NOT OPEN
ment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manu-
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, al, may cause harmful interference to radio com-
munications.
DO NOT REMOVE COVER (OR BACK).
Operation of this equipment in a residential area is
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
likely to cause harmful interference in which case
VICING TO QUALIFIED SERVICE PERSONNEL.
the user will be required to correct the interference
at his own expense.
FCC Caution: To assure continued compliance,
The lightning flash with arrowhead
(example - use only shielded interface cables when
symbol, within an equilateral trian-
connecting to computer or peripheral devices). Any
gle, is intended to alert the user to
changes or modifications not expressly approved
the presence of uninsulated "dan-
by the party responsible for compliance could void
gerous voltage" within the product's
the user's authority to operate this equipment.
enclosure that may be of sufficient
SA 1965 magnitude to constitute a risk of
The serial number of this product may be found on
electric shock to persons.
the bottom of the unit.
You should note the serial number of this unit in the
space provided and retain this instruction as a per-
The exclamation point within an
manent record of your purchase to aid identification
equilateral triangle is intended to
in the event of theft.
alert the user to the presence of
important operating and mainte-
Model No.
nance (servicing) instructions in the
literature accompanying the appli- Serial No.
ance.
SA 1966
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
PREFACE
Panasonic's WV-CP240/CP242/CP244 series digi-
transfer CCD image sensor having 768 horizontal
tal signal processing color CCD cameras intro- pixels (picture elements), and digital signal pro-
duce a new level of high picture quality and high cessing LSI's. This model offers cutting-edge
resolution through the use of a 1/3-inch interline
technology for advanced video surveillance.
FEATURES
1. The following functions are built in. 2. Minimum illumination of 0.6 lx (0.06 foot-can-
(1) Auto Light Control (ALC)/Electronic Light dle) at F0.75 (equivalent to 2.0 lx (0.2 foot-
Control (ELC) candle) at F1.4)
(2) Automatic Gain Control (AGC) +15 dB
and Automatic Tracing White Balance 3. Signal-to-noise ratio of 50 dB
(ATW) (Equivalent to AGC Off)
(3) Camera synchronization mode selec-
table between internal (INT), Line-locked 4. Horizontal resolution of 480 lines
(LL) for WV-CP240 and WV-CP244 and
Multiplexed Vertical Drive (VD2). 5. Auto iris lens control selectable between
video signal and DC power supply.
PRECAUTIONS
1. Do not attempt to disassemble the camera. 4. Do not use strong or abrasive detergents
To prevent electric shock, do not remove when cleaning the camera body.
screws or covers. Use a dry cloth to clean the camera when
There are no user serviceable parts inside. dirty.
Ask a qualified service person for servicing. In case the dirt is hard to remove, use a mild
detergent and wipe gently. Afterwards, wipe
2. Handle the camera with care. off the remained part of the detergent in it
Do not abuse the camera. Avoid striking, with a dry cloth.
shaking, etc. The camera could be damaged
by improper handling or storage. 5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive
3. Do not expose the camera to rain or detergents. Use lens tissue or a cotton tipped
moisture, or try to operate it in wet areas. applicator and ethanol.
Turn the power off immediately and ask a
qualified service person for servicing. 6. Never face the camera towards the sun.
Moisture can damage the camera and also Do not aim the camera at bright objects.
create the danger of electric shock.
Whether the camera is in use or not, never
Caution:
aim it at the sun or other extremely bright
To prevent fire or electric shock hazard, use
objects. Otherwise, blooming or smear may
a UL listed cable (VW-1, style 1007) for the
be caused.
DC 12 V or AC 24 V Input Terminal.
7. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Use the camera under conditions where tem-
perature is between –10°C - +50°C (14°F -
122°F), and humidity is below 90 %. The
input power source is 120 V AC 60 Hz for
WV-CP240, 12 V DC for WV-CP242, and 24 V
AC 60 Hz for WV-CP244.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
<WV-CP240>
BLC ON
ALC
Printed in Japan
ALC BLC ON
VIDEO SHARP INT VIDEO SHARP INT
N 19
VIDEO OUT
DC SOFT LL
ELC OFF
For U.S.A
<WV-CP244>
DC SOFT LL
ELC OFF
AC 24V IN
GND
WV–
1 2
ALC BLC ON
VIDEO SHARP INT
VIDEO OUT
DC SOFT LL
ELC OFF
ALC BLC ON
<WV-CP242>
VIDEO SHARP
DC 12V IN
DC SOFT
ALC BLC ON ELC OFF
VIDEO SHARP
VIDEO OUT
DC SOFT
ELC OFF
q Auto Iris Lens Connector ON: Select this mode when a strong light
Supplies power and control signals to an auto
iris lens (not supplied). OFF: Normal picture.
!1 Detail/Aperture Level Selector (SHARP,
w Flange-back Adjusting Ring
This ring adjusts the back-focal distance or SOFT)
The detail/aperture level can be selected with
picture focus. Rotate this ring clockwise for a
C-mount lens or counterclockwise for a CS- this selector. Set it to the desired position
while observing the picture on the monitor.
mount lens.
SHARP: Normal position.
e Lens (option) SOFT: Select this position when a Quad
r Mount Adapter
!2 Automatic Light Control/Electronic Light
The camera mounting screw hole is for
Control Selector (ALC, ELC)
mounting the camera onto a mounting brack-
et. The camera is originally designed to be Lets you select the mode according to the
mounted from the bottom, however, a top- lens type used.
ALC: Select this mode when an auto iris lens
mounting type is also available. To mount
from the top, remove the mount adapter from
the bottom of the camera by removing two ELC: Select this mode when a fixed iris lens
fixing screws. Attach the mount adapter to
the top as shown in the diagram, then mount
the camera on the mounting bracket. Make
sure that two original screws are used when !3 Lens Drive Signal Selector (VIDEO, DC)
mounting the mount adapter; longer type Lets you select the mode according to the
type of auto iris lens drive signal to be sup-
screws may damage inner components, too
shorter type screws may cause the camera plied to the lens from the auto iris lens con-
drop. nector.
VIDEO: Select this mode if you are using a
t Focus Fixing Screw
y Power Cord (only for WV-CP240) DC: Select this mode if you are using a auto
Connect this power cord to an electrical out-
let of 120 V AC 60 Hz.
!4 Video Output Connector (VIDEO OUT)
u DC 12 V Input Terminal This connector is for connecting with the
[DC 12V IN (only for WV-CP242)] VIDEO IN connector of the video monitor.
This terminal is for connecting the 12 V DC Whenever the multiplexed vertical drive (VD2)
power supply cord. signal is supplied to this connector, the cam-
era synchronization mode is automatically set
i AC 24 V Input Terminal to Vertical Drive.
[AC 24V IN (only for WV-CP244)]
This terminal is for connecting the 24 V AC
60Hz power supply cord.
Cautions:
• Connect to 12 V DC (10.5 V-16 V) or 24 V
o Synchronization Mode Selector
AC (19.5 V-28 V) class 2 power supply only.
[INT, LL (only for WV-CP240 and WV-
Make sure to connect the grounding lead to
CP244)]
the GND terminal when the power is sup-
Selects the camera synchronization mode as
plied from a 24 V AC power source.
either internal sync mode (INT) or line-lock
• To prevent fire or electric shock hazard, use
mode (LL).
a UL listed cable (VW-1, style 1007) for the
INT: Sets to internal 2:1 interlace.
DC 12 V or AC 24 V Input Terminal.
LL: Sets to Line-lock mode.
!0 Back Light Compensation Mode Selector
(BLC ON, OFF)
Lets you select the mode according to the
position of the object and light conditions on
the screen.
CONNECTIONS
A. WV-CP240 (120V AC 60Hz)
Connect the power cord to an electrical outlet
of 120V AC 60Hz.
B. WV-CP242 (12V DC)
Connect the power cord to the DC 12V IN ter-
minal on the rear panel of the WV-CP242.
@ !
12 V DC
(10.5 V - 16 V)
Resistance of copper wire [at 20°C (68°F)]
Copper wire #24 #22
size (AWG) (0.22mm 2 ) (0.33mm 2 ) (0.52mm
LOCK
Resistance
0.078 0.050
Ω/m
Resistance
0.026 0.017
Ω/ft
• Calculation of maximum
between camera and power supply :
CP244
10.5V DC ≤ V − (R x 0.42 x L) ≤ 16V DC
A
L : Cable length (meters)
R : Resistance of copper wire (Ω/meter)
V : DC output voltage of power supply unit
A
− 12
V
A
L standard = (meters)
0.42 x R
− 16
V
Mount Adapter A
L minimum = (meters)
0.42 x R
− 10.5
V
A
L maximum = (meters)
0.42 x R
C. WV-CP244 (24V AC 60Hz)
Connect the power cable to the AC 24 V IN
terminal on the rear panel of the WV-CP244.
such as a spotlight is in the background.
1 2
24 V AC, 60 Hz
(19.5 V - 28 V)
System is connected to this camera. Recommended wire gauge sizes for 24 V AC line
Copper wire #24 #22
size (AWG) (0.22mm 2 ) (0.33mm 2 ) (0.52mm
(m) 95 150
Length
of Cable
(Approx.)
(ft) 314 495
(ALC lens) is used with this camera.
Caution:
or manual iris lens is used with this cam-
To prevent fire or electric shock hazard, use
era.
a UL listed cable (VW-1, style 1007) for the
DC 12 V or AC 24 V Input Terminal.
Video Cable
1. It is recommended to use a monitor whose
resolution is at least equal to that of the
auto iris lens that requires a video drive
camera.
signal.
2. The maximum extensible coaxial cable
length between the camera and the moni-
iris lens that requires a DC drive signal.
tor is shown below.
Type of RG-59/U RG-6U RG-11/U RG-15/U
coaxial cable (3C-2V) (5C-2V) (7C-2V)
Recommended (m) 250 500
maximum
cable length (ft) 825 1 650
FOCUS OR FLANGE-BACK ADJUSTMENT
The following adjustment should be made by
qualified service personnel or system installers.
q Loosen the screw on the side of the camera.
Focusing of Focusing of
CS-mount lens
C-mount lens
Focus Fixing Screw
Flange-back
Adjusting Ring
SPECIFICATIONS
Installation of Auto Iris Lens Pick-up Device:
Scanning Area:
Connector
Install the lens connector (YFE4191J100) when Synchronization:
using a video drive ALC lens.
The installation should be made by qualified Scanning System:
service personnel or system installers. Scanning:
Cut the iris control cable at the edge of the lens
Horizontal:
connector to remove the existing lens connector Vertical:
and then remove the outer cable cover of the sup- Horizontal Resolution:
plied connector as shown in the diagram.
Video Output:
The pin assignment of the lens connector is as fol- Signal-to-Noise Ratio:
lows: Electronic Light Control:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used Minimum Illumination:
Pin 3: Video signal; 0.7 V[p-p]/40 kΩ
Pin 4: Shield, ground Detail:
Lens Mount:
Rib Ambient Operating Temperature:
Pin 3
Ambient Operating Humidity:
Pin 1
Power Source and
Power Consumption:
Pin 4
#20 #18
Pin 2
Dimensions (without lens):
2 ) (0.83mm 2 )
0.03. 0.018
Solder the lens cable to the pins of the sup-
Weights (without lens):
plied connector.
0.010 0.006
cable length
Mounting the Lens
Weights and dimensions indicated are approximate.
Caution:
Before you mount the lens, loosen the screw Specifications are subject to change without notice.
on the side of the camera, and rotate the
flange-back adjusting ring clockwise until it
stops. If the ring is not at the end, the inner
lens or CCD image sensor may be damaged.
q Mount the lens by turning it clockwise on the
STANDARD ACCESSORIES
lens mount of the camera.
w Connect the lens cable to the auto iris lens
connector on the side of the camera. Body Cap............................................................................................1 pc.
ALC Lens Connector (YFE4191J100).................................................1 pc.
Focus Fixing Screw
OPTIONAL ACCESSORIES
q
Lenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, WV-LA908C3,
w
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount
(1"-32UN) and the lens weight should be less than
450 g (0.99 lbs). If the lens is heavier, both the
#20 #18
2 ) (0.83mm 2 )
lens and camera should be secured by using the
255 425 supporter.
The protrusion at the rear of the lens should be as
842 1 403
shown in the diagram.
C-mount: Less than 13 mm (1/2")
CS-mount: Less than 8 mm (5/16")
(10C-2V)
600 800
1 980 2 640
w Turn the flange-back adjusting ring to the
desired position.
Caution: When the C-mount lens is mounted,
do not rotate the ring counterclockwise
by force after it stops. If the ring is rotat-
Panasonic Digital Communications & Security Company
ed by force, the inner lens or CCD image
Unit of Matsushita Electric Corporation of America
sensor may be damaged.
Security Systems Group
www.panasonic.com/cctv
e Tighten the screw on the side of the camera.
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Zone Office
Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Caution: Tightening the screw by force will
Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
cause damage to the screw or deviation Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
of focus.
2003
768 (H) x 494 (V) pixels, Interline Transfer CCD
4.92 (H) x 3.70 (V) mm (Equivalent to scanning area of 1/3"
pick-up tube)
Internal, Line-locked or Multiplexed vertical drive (VD2),
selectable
2 : 1 interlace
525 lines / 60 fields / 30 frames
15.734 kHz
59.94 Hz
480 lines
1.0 V[p-p] NTSC composite 75 Ω / BNC connector
50 dB (Equivalent to AGC Off, weight On)
Equivalent to continuous variable shutter speed between 1/60 s
and 1/15 000 s
0.6 lx (0.06 foot-candle) at F0.75 [equivalent to 2.0 lx (0.2 foot-
candle) at F1.4] AGC On
SHARP or SOFT, selectable
C-mount or CS-mount, selectable
−10°C - +50°C (14°F - 122°F)
Less than 90 %
WV-CP240: 120 V AC 60 Hz, 3.6 W
WV-CP242: 12 V DC, 270 mA
WV-CP244: 24 V AC 60 Hz, 3.3 W
67 mm (W) x 65 mm (H) x 123 mm (D)
2-5/8" (W) x 2-9/16" (H) x 4-13/16" (D)
WV-CP240: 0.48 kg (1.06 lbs)
WV-CP242: 0.3 kg (0.66 lbs)
WV-CP244: 0.33 kg (0.73 lbs)
WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LFY3C3,
WV-LFY45C3, WV-LFY9C3
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,
P.R. 00985 (809)750-4300
© Matsushita Electric Industrial Co., Ltd. All rights reserved.