Related Manuals for Philips Brilliance 272B7QUPBEB
Summary of Contents for Philips Brilliance 272B7QUPBEB
- Page 1 Brilliance 272B7 241B8 www.philips.com/welcome EN User manual Customer care and warranty 23 Troubleshooting & FAQs...
-
Page 2: Table Of Contents
6.1 Resolution & Preset Modes ..21 7. Power Management ....22 8. Customer care and warranty . 23 8.1 Philips’ Flat Panel Monitors Pixel Defect Policy ....23 8.2 Customer Care & Warranty ..26 9. Troubleshooting & FAQs ..27 9.1 Troubleshooting ...... -
Page 3: Important
• Please use approved power cord and production number of the product. provided by Philips all the time. If your power cord is missing, please 1.1 Safety precautions and contact with your local service maintenance center. - Page 4 1. Important • To avoid the risk of shock or continuous screen use is likely to be better than a 15-minute break permanent damage to the set, do every two hours. Try to keep your not expose the monitor to dust, eyes from eye strain while using the rain, water, or excessive moisture screen for a constant period of time...
-
Page 5: Notational Descriptions
1. Important Warning 1.2 Notational Descriptions Failure to activate a screen saver, or The following subsections describe a periodic screen refresh application notational conventions used in this may result in severe “burn-in” or “after- document. image” or “ghost image” symptoms that will not disappear and cannot be Notes, Cautions and Warnings repaired. -
Page 6: Disposal Of Product And Packing Material
From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled. At Philips, end- of-life management primarily entails participation in national take-back This marking on the product or on... -
Page 7: Setting Up The Monitor
Top Victory Investments Ltd. or one of its affiliates. Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. used under license. - Page 8 USB C driver. You can find the “LAN Drivers” from CD Step 2 disk if bundled or go to Philips website support page to download the driver. USB C USB C-C Please follow the steps for the...
- Page 9 2. Setting up the monitor Note Please contact Philips service hotline for Mac address clone tool as necessary. USB hub To comply with International energy...
-
Page 10: Operating The Monitor
What is On-Screen Display (OSD)? Description of the control buttons On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. - Page 11 2. Setting up the monitor Note If this display has "DPS" for ECO design, the default setting is "ON" mode: it makes the screen looks slightly dim; for optimum brightness, enter to the OSD to set "DPS" to "OFF" mode. Main menu Sub menu 0, 1, 2, 3, 4...
- Page 12 2. Setting up the monitor Resolution notification Height adjustment This monitor is designed for optimal performance at its native resolution, 2560 × 1440 @ 60 Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 2560 ×...
-
Page 13: Remove The Base Assembly For Vesa Mounting
2. Setting up the monitor Note 2.3 Remove the Base Assembly This monitor accepts a 100mm x 100mm for VESA Mounting VESA-Compliant mounting interface. Before you start disassembling the VESA Mounting Screw M4. Always monitor base, please follow the contact manufacturer for wall-mount instructions below to avoid any possible installation. -
Page 14: Image Optimization
There are multiple selections: EasyRead, Office, Photo, Movie, Game, Economy, How does it work? LowBlue Mode and Off. SmartImage is an exclusive, leading edge Philips technology that analyzes the content displayed on your screen. Based on a scenario you select, ... - Page 15 Developed for wellbeing, temperature of the monitor. Philips LowBlue Mode setting uses a smart software technology to • Office: Enhances text and dampens reduce harmful shortwave blue brightness to increase readability light.
-
Page 16: Smartcontrast
3. Image Optimization 3.2 SmartContrast What is it? Unique technology that dynamically analyzes displayed content and automatically optimizes a Monitor's contrast ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter images or dimming backlighting for clear display of images on dark backgrounds. -
Page 17: Powersensor
4. PowerSensor™ detection signal for distances up to 4. PowerSensor™ 120 cm or 47 inches. (Setting 4) • Since some dark colored clothing How does it work? tends to absorb infrared signals even when the user is within 100 cm • PowerSensor works on principle or 40 inches of the display, step up of transmission and reception of... - Page 18 4. PowerSensor™ returned to its default Landscape position. Note A manually selected PowerSensor mode will remain operational unless and until it is readjusted or the default mode is recalled. If you find that the PowerSensor is excessively sensitive to nearby motion for some reason, please adjust to a lower signal strength.
-
Page 19: Daisy-Chain Function
“Clone” and connections “Extend”, enter the following OSD manual path for the selection: OSD / This Philips display is equipped with Setup / DP Out Multi-Stream / Clone, DisplayPort 1.2 interface which enables Extend. daisy-chaining to multiple displays. -
Page 20: Technical Specifications
6.Technical Specifications 6. Technical Specifications Picture/Display Monitor Panel Type IPS Technology Backlight Panel Size 27" W (68.5 cm) Aspect Ratio 16:9 Pixel Pitch 0.2331(H) mm x 0.2331(V) mm SmartContrast 50,000,000:1 Response Time (typ.) 14 ms(GtG) SmartResponse Time (typ.) 5 ms(GtG) Optimum Resolution 2560 x 1440 @ 60 Hz Viewing Angle... - Page 21 6.Technical Specifications Pivot 90 degree Power AC Input AC Input AC Input Consumption Voltage at Voltage at Voltage at 100VAC , 50Hz 115VAC , 50Hz 230VAC, 50Hz Normal Operation 44.00W (typ.) 44.10W (typ.) 44.20W (typ.) Sleep (Standby) <0.5W <0.5W <0.5W <0.3W <0.3W <0.3W...
- Page 22 Finish Texture Note 1. This data is subject to change without notice. Go to www.philips.com/support to download the latest version of leaflet. 2. Smart response time is the optimum value from either GtG or GtG (BW) tests. 3. USB hub is only support mouse or keyboard to wake up the system while on power saving mode.
-
Page 23: Resolution & Preset Modes
6.Technical Specifications 6.1 Resolution & Preset Modes Maximum Resolution 2560 x 1440 @ 75 Hz (digital input) Recommended Resolution 2560 x 1440 @ 60 Hz (digital input) H. freq Resolution V. freq (Hz) (kHz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00... -
Page 24: Power Management
7.Power Management 7. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, m o u s e o r o t h e r i n p u t d e v i c e i s detected, the monitor will 'wake up' automatically. -
Page 25: Customer Care And Warranty
Pixel Defect Policy single black pixel. Other combinations of lit and dark sub pixels appear as Philips strives to deliver the highest single pixels of other colors. quality products. We use some of the industry's most advanced... - Page 26 Black Dot Defects the warranty period, a TFT Monitor Black dot defects appear as pixels or panel in a Philips flat panel monitor sub pixels that are always dark or 'off'. must have pixel or sub pixel defects That is, a dark dot is a sub-pixel that...
- Page 27 8.Customer care and warranty BRIGHT DOT DEFECTS ACCEPTABLE LEVEL 1 lit subpixel 2 adjacent lit subpixels 3 adjacent lit subpixels (one white pixel) Distance between two bright dot defects* >15mm Total bright dot defects of all types BLACK DOT DEFECTS ACCEPTABLE LEVEL 1 dark subpixel 5 or fewer...
-
Page 28: Customer Care & Warranty
Please contact our Philips Customer Service Representative or local contact center (by Consumer care number) for more details. Philips Customer Care Center number listed below. -
Page 29: Troubleshooting & Faqs
• Contact with Philips customer • First, ensure that the power button service representative immediately. on the front of the monitor is in the... - Page 30 "burn-in", also Service contact information listed in known as "after-imaging" or "ghost Important information manual and imaging", on your screen. "Burn-in", contact Philips customer service "after-imaging", or "ghost imaging" representative. is a well-known phenomenon in * Functionality different according to LCD panel technology.
-
Page 31: General Faqs
• Shut down your computer, that the panel surface is not disconnect your old monitor and subjected to excessive shocks reconnect your Philips LCD monitor. and is protected from sharp or • Turn on your monitor and then turn blunt objects. When handling the on your PC. - Page 32 “burn-in” or “after- any PC, workstation or Mac? image” or “ghost image” symptoms Ans.: Yes. All Philips LCD monitors are that will not disappear and cannot be fully compatible with standard repaired. The damage mentioned above...
- Page 33 In Ans.: Important Information manual that case, it may not recognize can be download on the Philips and block the Philips USB type C website support page. power charging function. This is Q15: When I project from my notebook not a fault of the Philips display.
- Page 34 Top Victory Investments Ltd. or one of its affiliates. Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. used under license.