Sony KL-X9200J Operating Instructions Manual page 9

Preset and user m odes
The monitor automatically detects input signals with a
horizontal scanning frequency between 24.8 and 85.0
kHz and a vertical scanning frequency between 50 and
85 Hz. However, it is recommended that a signal with a
vertical scanning frequency of 60 Hz is used since the
screen may go blank for a few seconds whenever a
signal other than 60 Hz is input to the monitor.
The monitor is capable of a display resolution of up to
1,024 × 768 dots. When a signal with a higher resolution
is input, it will be processed to display the image at
1,024 × 768 dots.
Preset m odes
The monitor has the factory preset modes for the most
popular industry standards as shown below.
No. Resolution f H
(dots × lines) (kHz)
640 × 350*
1 31.469
640 × 400*
2 24.823
640 × 480
3 31.469
640 × 480
4 35.000
640 × 480
5 37.861
640 × 480
6 37.500
640 × 480
7 43.269
720 × 400
8 31.469
720 × 400
9 37.927
800 × 600
10 35.156
800 × 600
11 37.879
800 × 600
12 48.077
800 × 600
13 46.875
800 × 600
14 53.674
832 × 624
15 49.727
1024 × 768
16 35.522
1024 × 768
17 48.363
1024 × 768
18 56.476
1024 × 768
19 60.023
1024 × 768
20 60.241
1024 × 768
21 68.677
1152 × 864
22 67.500
1152 × 870
23 68.681
1280 × 960
24 60.000
1280 ×1024
25 46.433
1280 ×1024
26 63.981
1280 ×1024
27 79.976
* The monitor projects the picture in 4:3 aspect ratio.
Downloaded from: https://www.usersmanualguide.com/
f V Graphics Sync
(Hz) m ode
70.086 VGA mode 1 H-pos V-neg
56.416 PC-9801 Normal H-neg V-neg
59.940 VGA mode 3 H-neg V-neg
66.667 Macintosh 13" H-neg V-neg
72.809 VGA VESA 72 Hz H-neg V-neg
75.000 VGA VESA 75 Hz H-neg V-neg
85.008 VGA VESA 85 Hz H-neg V-neg
70.087 VGA mode 2 H-neg V-pos
85.039 VGA VESA 85 Hz H-neg V-pos
56.250 SVGA VESA 56 Hz H-pos V-pos
60.317 SVGA VESA 60 Hz H-pos V-pos
72.188 SVGA VESA 72 Hz H-pos V-pos
75.000 SVGA VESA 75 Hz H-pos V-pos
85.061 SVGA VESA 85 Hz H-pos V-pos
74.553 Macintosh 16" H-neg V-neg
43.479 XGA VESA 43 Hz H-pos V-pos
60.004 XGA VESA 60 Hz H-neg V-neg
70.069 XGA VESA 70 Hz H-neg V-neg
75.029 XGA VESA 75 Hz H-pos V-pos
74.927 Macintosh 19" H-neg V-neg
84.997 XGA VESA 85 Hz H-pos V-pos
75.000 SXGA VESA 75 Hz H-pos V-pos
75.060 Macintosh 21" H-neg V-neg
60.000 SXGA VESA 60 Hz H-pos V-pos
43.436 SXGA VESA 43 Hz H-pos V-pos
60.020 SXGA VESA 60 Hz H-pos V-pos
75.025 SXGA VESA 75 Hz H-pos V-pos
User m odes
When using a video mode that is not one of the preset
modes, some fine tuning may be required to optimize
the display to your preference. Simply adjust the
monitor according to the adjustments instructions on
pages 16 through 18 . The adjustments will be stored
automatically and recalled whenever that mode is
used.
Recom m ended horizont al t im ing
condit ions
Horizontal sync width should be more than 1.0 µsec.
Horizontal blanking width should be more than 3.6
µsec.
If t he f requency range of an input
signal is not accept able f or t he
m onit or
"OUT OF SCAN RANGE" appears on the screen.
The monitor does not accept an interlace mode
signal that is not a preset mode signal. Furthermore,
if you input a signal other than a preset mode signal
with a dot clock of more than 140 MHz, the picture
may be distorted.
Plug & Play
This monitor complies with the DDC
which are the Display Data Channel (DDC) standards
of VESA.
When a DDC1 host system is connected, the monitor
synchronizes with the V. CLK in accordance with the
VESA standards and outputs the EDID (Extended
Display Identification Data) to the data line.
When a DDC2B host system is connected, the monitor
automatically switches to each communication.
1 and DDC2B
TM
(cont inued)
9
Get t ing St art ed -GB
GB