Big Agnes COPPER SPUR HV UL mtnGLO Setup Instructions

COPPER SPUR HV UL & HV UL mtnGLO® SET UP INSTRUCTIONS
1. Remove contents from stuff sack. Spread tent body out over your desired camp site.
2. Stake out the four corners of the tent body.
3. UL 2, 3, 4 & 5 assemble the two poles: One main pole with a 4-way hub and one short
straight crossover pole. UL1 assemble one main pole with two hubs and an attached
crossover pole. To ensure each pole section is fully seated insert each pole section into
the next by hand, instead of allowing the shock cord to snap them together.
4. Position the assembled main pole on top of the tent body. Match the colors of the pole
ends with the matching colors of the webbing on the tent body.
5. Insert the pole tips into the keyed hole on the TipLok Buckle™ at the four corners of the
tent.
6. Attach the plastic clips on the tent body to the main pole.
7. UL2, 3, 4 & 5 place the crossover pole across the top of the main pole. The crossover pole
on UL1 is already attached to the main pole.
8. Clip the ends of the crossover pole into the clear plastic Ball Cap clips that are located
above the doors of the tent body. UL 2, 3, 4 & 5 attach the center plastic clip on the tent
body to the crossover pole.
9. Drape the rainfly over the tent body and match the colors of the webbing on the fly with
the webbing on the body.
10. Insert the tips of the crossover pole into the small pockets located on the underside of
the fly.
11. Attach all Velcro® tabs on the underside of the fly to the corresponding pole sections for
best stability.
12. Make sure the webbing at the corners of the rainfly is completely slackened. Attach the
buckles on the rainfly to those on the tent body.
13. Tighten the webbing on each buckle as needed to keep the rainfly taut.
14. Stake out the vestibules then stake out all remaining guylines.
15. Low Vent Set Up: For increased ventilation, hook the cord located at the bottom of the
vestibule door to the toggle at the top of the zipper located on the underside of the fly
16. Awning Set Up: Unzip the two zippers at the head-end of the tent, attach extra guylines
(included in stake bag) to corner cord loops, adjust trekking poles to desired height,
insert trekking pole tips through grosgrain loop or cord loop on corners of panel. Stake
out guylines.
Separate 6" length pole segment included for emergency
field repair. Slide repair pole over the break to act as a splint.
If you purchase the optional Big Agnes footprint for your tent, it will enable you to pitch a Fast
Fly shelter while leaving the tent body behind. The Fast Fly configuration requires the footprint,
tent fly, poles and stakes.
1. Lay the footprint on the ground and stake out.
2. UL 2, 3, 4 & 5 assemble the two poles: One main pole with a 4-way hub and one short
straight crossover pole. UL1 assemble one main pole with two hubs the crossover pole
is attached to the main pole. To ensure each pole section is fully seated insert each pole
section into the next by hand, instead of allowing the shock cord to snap them together.
3. Position the assembled main pole on top of the footprint. Match the colors of the pole
ends with the matching colors of the webbing on the footprint.
4. Insert the pole tips into the grommets at the four corners of the footprint.
5. UL2, 3, 4 & 5 insert the tips of the crossover pole into the small pockets located on the
underside of the fly.
6. UL2, 3, 4 & 5 with the crossover pole now attached to the fly drape the rainfly over the
pole frame. UL1 drape the rainfly over the pole frame, then insert the tips of the crossover
pole into the small pockets located on the underside of the fly.
7. Match the webbing colors on the fly with the matching colors of the webbing on the
footprint.
8. Attach all Velcro® tabs on the underside of the fly to the corresponding pole sections for
best stability.
9. Make sure the webbing at the corners of the rainfly is completely slackened. Attach the
buckles on the fly to those on the footprint.
10. Tighten the webbing on each buckle as needed to keep the rainfly taut.
11. Stake out the vestibules then stake out all remaining guylines.
12. Low Vent Set Up: For increased ventilation, hook the cord located at the bottom of the
vestibule door to the toggle at the top of the zipper located on the underside of the fly
13. Awning Set Up: Unzip the two zippers at the head-end of the tent, attach extra guylines
(included in stake bag) to corner cord loops, adjust trekking poles to desired height,
insert trekking pole tips through grosgrain loop or cord loop on corners of panel. Stake
out guylines.
Copper Spur HV UL1 Tent Body and Fly
BA Tiplock
TipLok Tent Buckle™
Cut here to remove. Do Not Tear!
Secure splint in place with tape.
FAST FLY SET UP INSTRUCTIONS
Copper Spur HV UL4 and HV UL5 Tent Body and Fly
Copper Spur HV UL2 and HV UL3 Tent Body and Fly
Hardware:
Ball Cap