Noise/Vibration Information - Bosch Professional GCO 2000 Original Instructions Manual

17 Tool arm
18 Transport handle
19 Blade guard
20 Spark guard
21 Tool spindle
22 Clamping flange
23 Washer
24 Hexagon bolt
25 Lock nut of the depth stop
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Cut off grinder
Article number
3 601 L17 ...
Rated power input
No-load speed
Soft starting
Weight according to
EPTA-Procedure 01/2003
Protection class
Permissible workpiece dimensions (maximum/minimum) see page 19.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimensions of suitable cutting discs
Cutting disc diameter, max.
Cutting discs width, max.
Mounting hole diameter
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 61029-1, EN 61029-2-10.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 17.09.2014
Bosch Power Tools
GCO 2000
... 20.
... 27. ... 26.
W 2000 1650
-1
min 3500 3500

kg 18
/II
mm
mm
mm
Helmut Heinzelmann
Head of Product Certification
PT/ETM9

Noise/Vibration Information

Sound emission values determined according to
EN 61029-2-10.
Typically the A-weighted noise levels of the product are:
Sound pressure level 77 dB(A); Sound power level 88 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 61029:
2
a =3.0 m/s , K=1.5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also

take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
18
nificantly reduce the exposure level over the total working pe-
riod.
/II
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
355
3
 Avoid unintentional starting of the machine. During as-
25.4
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the ac-
cessories provided.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Cut-off grinder with mounted cutting disc
– Ring spanner 14
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
English | 17
(triax vector sum) and uncertainty K
h
2
.
1 609 92A 0Y1 | (17.9.14)