Advertisement
X-Array Install
plug baffle and lift the baffle assembly out
of the enclosure. Remove the remaining
four screws securing the 10-inch midbass
and lift the driver out of the enclosure. In
the event of failure, the entire woofer must
be replaced.
LF: First remove the grille, then remove the
screws securing the hatch on the front of
the enclosure. In both the upper and lower
woofer hatches, four screws pass through
the midbass horn and must be removed.
The hatches and woofers may both be re-
moved without removing the midbass horn.
To remove the hatch under the high-fre-
quency horn, the HF horn must be removed
first. Remove the four screws securing the
12-inch woofer and lift the driver out of the
enclosure. In the event of failure, the en-
tire woofer must be replaced.
The following replacement parts are avail-
able from Electro-Voice Service in Bucha-
nan, Michigan:
LF: Complete woofer: EV Part No. 812-3074
MB: Complete woofer: EV Part No. 810-1663
HF: Diaphragm kit; EV Part No. 84233-XX
Architects' and Engineers'
Specifications:
The loudspeaker system shall be a three-way
tri- or bi-amplified system. The system shall
have two paralleled 12-inch, low-frequency
loudspeakers in sealed, slot-loaded enclo-
sures with a nominal impedance of 6 ohms
and 2.5 inch aluminum voice coils. The
low-frequency loudspeakers shall have a
power handling capacity of 600 watts with
a shaped pink-noise signal with a 6-dB crest
factor for 8 hours (as per ANSI/EIA RS-426
A) The mid-bass section shall be a horn-
loaded 10-inch driver with a 2.5-inch alu-
minum voice coil and a nominal impedance
of 16 ohms. The mid-bass driver shall have
a power-handling capacity of 300 watts for
8 hours (as per ANSI/EIA RS-426 A). The
high-frequency section shall be coaxially
mounted in one woofer manifold and shall
employ a 76.2-mm (3.0-inch) aluminum
voice coil, titanium-dome compression
driver capable of handling a 75 watt, 1,760-
to 20,000-Hz pink-noise signal with a 6-
dB crest factor for 8 hours (as per ANSI/
EIA RS426-A). The loudspeaker shall be
3
TM
Xi-2123/106 Loudspeaker System
constructed of 18-mm, 13-ply birch and
shall be trapezoidal in shape. The wedge
angle shall be 18-degrees.
The system shall be capable of very-high-level
operation with a bandwidth of 80 to 16,000
Hz. The system dimensions shall be 456 mm
(17.95 inches) wide by 1007 mm (39.65 inches)
high by 473 mm (18.64 inches) deep and shall
weigh 68.0 kg (150 lb). The system shall em-
ploy flying hardware of a "track" style and two
tracks on the enclosure top and two tracks on
the enclosure bottom (top and bottom refer-
ence to the 39.65-inch dimension.)
The loudspeaker shall be the Electro-Voice
Xi-2123/106.
Uniform Limited Warranty
Electro-Voice products are guaranteed against
malfunction due to defects in materials or work-
manship for a specified period, as noted in the
individual product-line statement(s) below, or in
the individual product data sheet or owner's
manual, beginning with the date of original pur-
chase. If such malfunction occurs during the speci-
fied period, the product will be repaired or re-
placed (at our option) without charge. The prod-
uct will be returned to the customer prepaid. Ex-
clusions and Limitations: The Limited Warranty
does not apply to: (a) exterior finish or appear-
ance; (b) certain specific items described in the
individual product-line statement(s) below, or in
the individual product data sheet or owner's
manual; (c) malfunction resulting from use or op-
eration of the product other than as specified in
the product data sheet or owner's manual; (d)
malfunction resulting from misuse or abuse of the
product; or (e) malfunction occurring at any time
after repairs have been made to the product by
anyone other than Electro-Voice Service or any
of its authorized service representatives. Obtain-
ing Warranty Service: To obtain warranty ser-
vice, a customer must deliver the product, pre-
paid, to Electro-voice Service or any of its au-
thorized service representatives together with
proof of purchase of the product in the form of a
bill of sale or receipted invoice. A list of autho-
rized service representatives is available from
Electro-Voice Service at 600 Cecil Street, Bucha-
nan, MI 49107 (800/234-6831 or FAX 616/
695-4743). Incidental and Consequential Dam-
ages Excluded: Product repair or replacement
and return to the customer are the only remedies
provided to the customer. Electro-Voice shall not
be liable for any incidental or consequential dam-
ages including, without limitation, injury to per-
sons or property or loss of use. Some states do
not allow the exclusion or limitation of incidental
or consequential damages so the above limita-
tion or exclusion may not apply to you. Other
Rights: This warranty gives you specific legal
rights, and you may also have other rights which
vary from state to state.
Electro-Voice Speakers and Speaker Sys-
tems are guaranteed against malfunction due
to defects in materials or workmanship for a
period of five (5) years from the date of origi-
nal purchase. The Limited Warranty does
not apply to burned voice coils or malfunc-
tions such as cone and/or coil damage re-
sulting from improperly designed enclo-
sures. Electro-Voice active electronics asso-
ciated with the speaker systems are guaran-
teed for three (3) years from the date of origi-
nal purchase. Additional details are included
in the Uniform Limited Warranty statement.
Electro-Voice Accessories are guaranteed
against malfunction due to defects in mate-
rials or workmanship for a period of one (1)
year from the date of original purchase. Ad-
ditional details are included in the Uniform
Limited Warranty statement.
Electro-Voice Flying Hardware (including
enclosure-mounted hardware and rigging ac-
cessories) is guaranteed against malfunc-
tion due to defects in materials or workman-
ship for a period of one (1) year from the
date of original purchase. Additional details
are included in the Uniform Limited War-
ranty statement.
For warranty repair, service information, or
a listing of the repair facilities nearest you,
contact the service repair department at:
616/695-6831 or 800/685-2606.
For technical assistance, contact Technical
Support at 800/234-6831 or 616/695-6831,
M-F, 8:00 a.m. to 5:00 p.m. eastern standard
time.
Specifications subject to change without notice.
Advertisement
