Related Manuals for Samsung PC6 UC N Series
Summary of Contents for Samsung PC6 UC N Series
- Page 1 Air conditioner Installation Manual PC6*UC**N • Thank you for purchasing this Samsung air conditioner. • Before operating this unit, please read this manual carefully and retain it for future reference.
- Page 2 Installing the 360 CST purification panel panels 1 Remove the protective cover. Type A: Square panel Type B: Circular panel Accessories M4 X L25 bolt (4) Installation manual (1) (Type A only) 2 Remove the electrical system unit cover. User manual (1) M4 screw (4) CAUTION •...
- Page 3 CAUTION indoor unit, and then tighten the screws. • If installing the AM********** model, make sure the two power lines, going into the indoor unit, are fastened using a single compressed ring terminal. CAUTION • Make sure the hooks on the air purification kit have been fastened properly.
-
Page 4: Installing The Grille
9 Remove the protective tape covering the dust sensor NOTE • If the grille is installed correctly, the indicator on the indoor unit is at a 90 degree angle with the Samsung engraved on the indoor unit is aligned with the triangle on the grille. - Page 5 2 Push the four corners of the panel front toward the 5 Place each cover panel on a corner of the panel front. indoor unit body one at a time until you hear “click” so that they are assembled in place. assembled to the panel front.
- Page 6 Installing the 360 CST purification panel Installing the circular panel on the indoor unit 1 Insert the decoration panel the indoor unit body. Then rotate the decoration panel clockwise until it is • Ceiling type • Open type NOTE • Make sure that the decoration panel is installed correctly so that there is no gap between the ceiling and the panel.
- Page 7 Setting the indoor unit address and setup options Common steps for setting the 2 Set the option values. addresses and options CAUTION • The total number of available options are 24: SEG1 to AR-KH0** remote control (for 360 cassette only) SEG24.
- Page 8 Setting the indoor unit address and setup options Take the steps presented in the following table: Steps Remote control display 1 Set the SEG2 and SEG3 values: a Set the SEG2 value by rotating the Wheel counterclockwise until the value you want to set appears on the remote control display.
- Page 9 Steps Remote control display 6 Press the (Mode) button. Fan and On appear on the remote control display. 7 Set the SEG9 and SEG10 values: a Set the SEG9 value by rotating the Wheel counterclockwise until the value you want to set appears on the remote control display.
- Page 10 Setting the indoor unit address and setup options Steps Remote control display a Set the SEG14 value by rotating the Wheel counterclockwise until the value you want to set appears on the remote control display. SEG14 the value you want to set appears on the remote control display.
- Page 11 Steps Remote control display 16 Press the (Mode) button. Fan and Off appear on the remote control display. 17 Set the SEG21 and SEG22 values: a Set the SEG21 value by rotating the Wheel counterclockwise until the value you want to set appears on the remote control display.
- Page 12 Setting the indoor unit address and setup options Set the indoor unit’s address and installation options with CAUTION the remote control. The address and indoor unit settings • The total number of available options are 24: SEG1 to the options individually. SEG24.
- Page 13 Take the steps presented in the following table: Steps Remote control display 1 Set the SEG2 and SEG3 values: a Set the SEG2 value by pressing the (Low Fan) button repeatedly until the value you want to set appears on the remote control display. SEG2 b Set the SEG3 value by pressing the (High Fan) button repeatedly until the value...
- Page 14 Setting the indoor unit address and setup options Steps Remote control display 6 Press the (Mode) button. Fan and On appear on the remote control display. 7 Set the SEG9 and SEG10 values: a Set the SEG9 value by pressing the (Low Fan) button repeatedly until the value you want to set appears on the remote control display.
- Page 15 Steps Remote control display a Set the SEG11 value by pressing the (Low Fan) button repeatedly until the value you want to set appears on the remote control display. SEG14 (High Fan) button repeatedly until the value you want to set appears on the remote control display. When you press the (Low Fan) or (High Fan) button, values appear in the...
- Page 16 Setting the indoor unit address and setup options Steps Remote control display 16 Press the (Mode) button. Fan and Off appear on the remote control display. 17 Set the SEG21 and SEG22 values: a Set the SEG21 value by pressing the (Low Fan) button repeatedly until the value you want to set appears on the remote control display.
- Page 17 3 Check whether the option values that you have set are correct by pressing the (Mode) button repeatedly. 1 Check if power is supplied to the indoor unit. [SEG2, SEG3] [SEG9, SEG10] • If the power supply is not connected, a separate power supply is required.