Table of Contents
Advertisement
• Periodically check the condition of the filters and, if dirty,
clean.
Filters which are very greasy may impair the performance of
the extractor system and even cause fires.
G.4
Electrical connection
IMPORTANT
The connection to the electrical power supply must
be in compliance with the current national and local
regulations.
Before connecting, make sure the voltage and frequency
match that given on the dataplate.
• Connect the appliance to the power supply in a permanent
way with an H05 RN-F type cable.
• Install the power cable in a metal or rigid plastic pipe without
any sharp parts.
If the appliance is connected using an existing cable, do not
insert the installation tube in the appliance.
Also make sure the tube has no sharp edges.
• An isolating switch of suitable current rating with a contact
breaking distance of at least 3 mm, and a 16 A delayed-
action T type fuse must be fitted upstream of the appliance.
The isolating switch must be installed near the appliance in
the permanent electrical system of the premises.
• Install a device (interlocked plug, lockable switch or similar
devices) lockable in the open position during maintenance
ahead of the appliance.
• Connect the appliance to an efficient earthing system.
The earthing conductor must therefore be connected to the
terminal marked by the symbol
terminal board.
• The appliance must also be connected to an equipotential
bonding system.
• Include also the appliance into an equipotential system.
This connection is made with the setscrew marked
located externally near the power cable entry.
The equipotential wire must have a section of at least 10
mm
2
.
G.4.1
Power cable installation
To connect the power cable to the appliance, proceed as
follows:
1. Undo the two screws "V" fixing the terminal board panel
under neath the appliance on the front left side;
2. Feed the power supply cable through cable clamp inlet
"B";
3. Connect the cable to terminal board "A" as shown in the
figure below;
4. Fasten with the corresponding cable clamp;
5. Remount the panel and secure with the fixing screws.
G.5
The appliance is equipped with the following safety devices:
Protection fuse
• It is located behind the control panel (see electrical wiring
Oven chamber safety thermostat
• It is mounted behind the control panel (manual reset type).
on the connection
Thermal cut-out inside fan motor
• If the fan motor overheats, the thermal cut-out trips and
,
G.6
G.6.1
• Gas ovens are not suitable for marine environment.
• The gas connection fitting is yellow.
IMPORTANT
The manufacturer declines any responsibility for
failure to comply with existing accident prevention
standards.
CAUTION
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in
order to avoid a hazard.
Safety devices
diagram). To replace:
1. unscrew the cap;
2. replace the blown fuse with another of the same rating.
The correct rating is indicated on the corresponding fuse
plate.
The safety thermostat shuts off the power supply to the
convection heating system.
IMPORTANT
The thermostat must only be reset by qualified
technicians after first eliminating the cause of the
fault.
blows fuse "F1", causing the appliance to shut down (see
electrical wiring diagram).
1. Eliminate first the cause of the fault;
2. Replace fuse "F1" with another of the same rating;
To replace the fuse:
– open the control panel;
– unscrew the cap;
– replace the blown fuse with another of the same rating.
The correct rating is indicated on the corresponding
fuse plate.
3. Reset the thermal cut-out.
NOTE!
Thermal cut resetting must only be done by
qualified technicians.
Gas connection
General information
CAUTION
Make sure the appliance corresponds with
the gas supply to which it is connected. If
the appliance does not correspond with
the gas supply, convert following the
instructions given in G.7 Conversion to
different type of gas paragraph.
Make sure the appliance is suitable for the
type of gas available. Refer to the
dataplate.
Observe all local gas company regula-
tions! Connecting incorrectly may result in
burns.
25
Advertisement
Table of Contents
