Related Manuals for Nady Systems PMX-1600
Summary of Contents for Nady Systems PMX-1600
- Page 1 O W N E R ’ S M A N U A L PMX SERIES PMX-600 — 6 Channel Powered Mixer w/DSP Effects PMX-1600 —16 Channel Powered Mixer w/DSP Effects...
-
Page 2: Table Of Contents
• Internal shielded AC supply with 115V(60Hz)/230V(50Hz) select switch • Dimensions & Weights: PMX-1600: (HWD) 6.4” x 28.7” x 17.2” (163 x 729 x 437mm); 35.25 lbs. (16 Kg) PMX-600: (HWD) 6.4” x 16.9” x 17.2” (163 x 430 x 437mm);... -
Page 3: Warning
ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR IMPORTANT SAFETY INSTRUCTIONS When using this electronic device, basic precautions should always be taken, including the following: Read all instructions before using the product. Do not use this product near water (e.g., near a bathtub, washbowl, kitchen sink, in a wet basement, or near a swimming pool, etc.). -
Page 4: Installation
[Please note: Nady Systems is not responsible for shipping damage. If your unit is damaged, do not return to Nady, but notify your dealer and the shipping company (if shipped to you) immediately to make a claim. Such claims must be made by the consignee in a timely manner.]... -
Page 5: Controls And Connections
C O N T R O L S A N D C O N N E C T I O N S 1. CHANNEL SECTION (1) MIC INPUT This electronically balanced XLR input is designed to accept signals from any balanced or unbalanced low impedance (Low Z) microphone. - Page 6 C O N T R O L S A N D C O N N E C T I O N S (5) CHANNEL PEAK LED The Peak LED illuminates when a channel input is overloading. It detects the peak level after the Equalizer Controls (7) and will light just before clipping to warn that the signal is approaching overload.
-
Page 7: Master Echo Effects Section
C O N T R O L S A N D C O N N E C T I O N S 2. AUX EFFECTS SECTION (14) AUX SEND 1 & 2 LEVEL CONTROLS These controls adjust the final mixed level of the channel Aux 1 and Aux 2 auxiliary signals separately. -
Page 8: Master Input / Output Section
C O N T R O L S A N D C O N N E C T I O N S outputs for easy monitoring. The Group can be a very useful feature if used effectively. For stage applications the Group mix can be sent to a monitor amplifier so the performers will only hear the audio that is not already loud enough on stage. -
Page 9: Rear Panel
C O N T R O L S A N D C O N N E C T I O N S (38) (40) (41) (37) (39) 5. REAR PANEL (37) SPEAKER OUTPUTS • RIGHT - These two 1/4” speaker output jacks are paralleled together for the Master Right output signal and can deliver up to 200W RMS to a 4 load. -
Page 10: Connection Example
C O N N E C T I O N S MONITOR SPEAKERS & POWER AMP OR USE SEPARATE CABLE REVERB PA or RECORDING DEVICE TAPE/DISK RECORDER... -
Page 11: Specifications
5. GENERAL Power Requirements ...Voltage selectable, 115VAC/60Hz or 230VAC /50Hz Fuse Requirements ...5x20mm glass tube F.B. 8A 250V @ 115VAC PMX-1600 Weight ... 35.25 lbs. (16 Kg) Dimensions (HWD) ...6.4” x 28.7” x 17.2” (163 x 729 x 437mm) PMX-600 Weight ...24.5 lbs. - Page 12 (U.S.) Should your NADY AUDIO product require service, please contact the Nady Service Department via telephone at (510) 652-2411, or e-mail at service@nady.com. (International) For service, please contact the NADY AUDIO distributor in your country through the dealer from whom you purchased this product.