Advertisement
MIDLAND G5 is a new generation PMR 446 transceiver that may be used, without license, in all the countries in which Pan-European PMR446 frequencies are authorised (446.00625 – 446.09375 MHz).
Please consult the "Restrictions on the use" chart for information regarding country specific limitations.
Specifications are subject to change without notice.
To open the battery compartment, hold the unit face down and slide the cover towards the bottom of the radio; then, insert 3 x AAA alkaline or rechargeable batteries.
Press once the button [3] to activate display illumination for approx. 7seconds. The display illumination can be also activated by pushing L [6] button and deactivated by pressing L again.
** Coverage
The maximum range is obtained during use in an open space.
The only limitation to maximum possible range are environmental factors such as blockage caused by trees, buildings, or other obstructions. Inside a car or a metallic constructions, the range can be reduced.
Hold the [3] button down for 3 seconds. The radio beeps 3 times with different tones (may be inhibited). The LCD [1] displays a "self-test" message for 1 second, it will then indicate the last channel selected.
To adjust the volume level, push ▼/▲ [2] buttons until you reach the desired level.
Press the [3] button once and then the ▼/▲ [2] controls to select one of the 8 channels. To confirm the selection, push PTT [7] or wait for 5 seconds roughly.
CHANNEL | FREQUENCY RX/TX (MHZ) |
01 | 446.00625 |
02 | 446.01875 |
03 | 446.03125 |
04 | 446.04375 |
05 | 446.05625 |
06 | 446.06875 |
07 | 446.08125 |
08 | 446.09375 |
For maximum speech clarity, hold the radio 4 to 10 cm away from your mouth, keep the PTT button [7] pressed and speak into the unit. During transmission the display shows:
When the PTT is released, the radio beeps to confirm to other users that your transmission has finished (This function is disabled by default, to enable it see paragraph "Roger Beep").
Simply release the PTT [7] button. When you receive a signal, display shows:
In your MIDLAND G5 the background noise reduction device (squelch) is activated by default.
MIDLAND G5 is supplied with an automatic current economy circuit. If the transceiver receives no signal for 7 seconds or longer the "power save function" automatically activates [1]. The battery life may increase by up to 50%.
When the batteries are in need of charging, icon will be displayed: it is necessary to replace the alkaline batteries or recharge the Ni-Cd/NiMH ones.
External charger jack. Insert the original charger plug into the CHG jack [8]. We recommend use of the appropriate charger only. Attention: alkaline batteries cannot be recharged.
Press and hold the SCAN [4] button for longer than 3 seconds: the display will show Lc to confirm activation. PTT [7] and L [6] buttons will still be active. Repeat the same procedure to unlock the keypad.
Press the [3] key for three times. The display shows "VOX" blinking at the top on the left, while on the right of the channel number, "of" appears. Select "on" by means of ▼/▲ [2] buttons and push the PTT [7] key, or simply await 5 seconds for confirmation.
Speak into the microphone [5]: the transmission is automatically activated.
Press the [3] key again. The display shows "VOX" blinking at the top on the left, while on the right of the channel number, "on" appears. Select "of" using the ▼/▲ [2] buttons and push the PTT [7] key, or simply await 5 seconds for confirmation.
When PTT [7] is released the radio will beep to confirm to other users that your transmission has finished. This feature is disabled by default.
To enable it, follow these steps:
The SCAN mode monitors the busy channels.
It is used to check the traffic radio on the 8 channels before transmitting and allows the unit to stop on a channel that someone is talking on. When the radio stops on a busy channel, the scan will resume after about 5 seconds.
To enable SCAN:
Transmission during the SCAN function
At the PTT [7] pressure, the radio will transmit on the channel where the scan started. To deactivate this function, push the SCAN [4] key again.
MIDLAND G5 can receive in two modalities:
To activate 38 different CTCSS tones in RX and TX follow these steps:
To deactivate CTCSS tones
If you want no CTCSS code:
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the G5 that isn't answered in the manual? Leave your question here.