Mobile mount and pcie adapter - front loader (23 pages)
Summary of Contents for Seagate Nytro XP7102
Page 1
Seagate® Nytro® XP7102 NVMe Flash Accelerator Card User Guide XP7102 -1A2048 XP7102-1A1024 100786980, Rev. A July 2016...
Page 2
Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Nytro, Nytro WarpDrive and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The NVM Express® design mark is a registered trademark of NVM Express, Inc. All other trademarks or registered trademarks are the property of their respective owners.
Authorized Service Centers For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/seagate-recovery-services/recover/ For Seagate OEM and Distribution partner and Seagate reseller portal, visit: http://www.seagate.com/partners Seagate Nytro XP7102 NVMe Flash Accelerator Card User Guide, Rev. A...
Seagate® Nytro® XP7102 Nytro™ CLI User Guide. The Nytro XP7102 is a half-height, half-length PCIe card that brings high performance with a low power requirement. The low power requirement makes cooling easier and allows you to add cards in a wider range of servers.
Insert the Nytro XP7102 card in a 25 W PCIe slot. Locate an empty 25 W PCIe slot. Without sufficient power the Nytro XP7102 card may be damaged or run at less than optimal performance. Remove the blank bracket panel on the server chassis that aligns with the empty PCIe slot.
Turn on the power. Use the next procedure to install the appropriate operating system drivers. UEFi The Nytro XP7102 card is UEFi -compatible with version 2.3.1. Seagate Nytro XP7102 NVMe Flash Accelerator Card User Guide, Rev. A...
Seagate Technology Support Services or, contact your FAE. Keep these tips in mind when reporting a problem: Clearly identify and report the revision level of the Nytro XP7102 card. To view this information in the command line interface tool, use the nytrocli list command with the respective controller number.
Nytro XP7102 Card Characteristics The Nytro XP7102 card uses a low-profile, half-height, and half-length PCIe board. The Nytro XP7102 card can be used for persistent or nonpersistent data, and offers high performance with low latency and a low CPU burden.
If the critical temperature warning persists, you might damage your card. Increase cooling speed or shut down your system to prevent damaging the card. The maximum sensor temperature for the Nytro XP7102 cards is 85 °C. The red LED lights up at 70°C to indicate a warning.
Characteristics Power Consumption for the Nytro XP7102 Card The Nytro XP7102 card receives power from the PCIe 12 V power rail. Use the following data for power consumption. Table 3 Nytro XP7102Card Power Consumption Card Idle Typical Power with I/O...
Characteristics Block Size The Nytro XP7102 card supports both 512 b and 4 K sector sizes. The default size is 4 K. LBA format change may require power cycle before the change takes effect. When you change the sector size, all data on the drive is destroyed. Make sure CAUTION there is no I/O activity to the drive before changing sector size.
• Consult the dealer or an experienced radio/TV technician for help. Shielded cables for SCSI connection external to the cabinet are used in the compliance testing of this Product. Seagate is not responsible for any radio or television interference caused by unauthorized modification of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Seagate Technology LLC.
Seagate uses an independent laboratory to confirm compliance with the directives/standards for CE Marking and RCM Marking. The Nytro XP7102 card was tested in a representative system for typical applications and complies with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. The selected system represents the most popular characteristics for test platforms.
X:表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。 X: Indicates that the hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement of GB/T26572. Seagate Nytro XP7102 NVMe Flash Accelerator Card User Guide, Rev. A...
Page 16
ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100786980, Rev. A...