Code Alarm CA 5051MT Owner's Manual
Code Alarm CA 5051MT Owner's Manual

Code Alarm CA 5051MT Owner's Manual

Manual transmission remote start and keyless entry system professional series

Advertisement

PROFESSIONAL
SERIES
CA 5051MT
Owner's Guide
Manual Transmission Remote
Start and Keyless Entry System
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
2010 Audiovox Electronics Corporation. All rights reserved.
1

Advertisement

Table of Contents
loading

Summary of Contents for Code Alarm CA 5051MT

  • Page 1 PROFESSIONAL SERIES CA 5051MT Owner’s Guide Manual Transmission Remote Start and Keyless Entry System IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply.
  • Page 2: Table Of Contents

    Table of Contents Using Your Remote Control ... 3 Using the Keyless Entry ... 3 Two Stage Door Unlock (optional) ... 3 Activating Trunk Release (optional) ... 3 Using the Progressive Car Finder Feature ... 3 Using the Personal Protection Alarm ... 3 Programmed Transmitter Notification ...
  • Page 3: Using Your Remote Control

    Using Your Remote Control Using the Keyless Entry button is used to lock the vehicle's doors, the vehicle's doors. To lock or unlock the doors simply press and release the desired function button one time. For your convenience, the parking lights will flash once when the doors are unlocked and twice when the door are locked.
  • Page 4: Valet Mode

    Valet Mode Valet Mode is used to disable the system from remote starting. To enter or exit valet mode simply follow the 4 steps outlined below: Turn the vehicle’s ignition ON. Push and hold the programming/valet button. The LED will turn on solid when valet mode is active Release the programming/valet button.
  • Page 5: Cancelling Remote Start Ready Mode

    Cancelling Remote Start Ready Mode The system will exit remote start ready mode if any of the following occur: Open any door Open the hood or trunk (if connected) Press the brake Release the parking brake Turn the ignition ON Remote Starting Your Vehicle To activate the remote start function, press and release the 2 seconds.
  • Page 6: User Programmable Run Time / Run Time Extension

    User Programmable Run Time / Run Time Extension The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle.
  • Page 7: Replacing Remote Control Batteries

    Replacing Remote Control Batteries 1-Way Remote Control: The batteries (model CR2016) inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim.
  • Page 8: Warranty Information

    Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below) should this Product under normal use and conditions, be proven defective in material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGI- NALLY INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for parts directly related to repairs of the defect(s).
  • Page 9 2010 Audiovox Electronics Corporation. All rights reserved.
  • Page 10 Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.

Table of Contents