Mitsubishi Electric MH2850U Supplementary Manual page 6

ITEM
HORIZ.POSITION
VERT. POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
OVER SCAN
HOLD
HOLD BEGIN
HOLD END
CLAMP POSITION
CLAMP WIDTH
VERT. SYNC
LPF
SHUTTER(U)
SHUTTER(L)
SHUTTER(LS)
SHUTTER(RS)
*1) Setting range differs depending on the input signals.
• Some commands are not executed depending on the input signal. The operational restrictions same as those
on the menu setting are applied. Refer to "Menu operation" in the User Manual for more details.
How to set the value
Use the ASCII or HEX code as shown below to set the value.
ASCII '+' '-'
HEX 2Bh 2Dh
[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are
ASCII codes.):
Sending commands
from the PC, etc.
30 30 41 50 4F 4E 31 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the
CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in
quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
30 30 53 0D
'0' '0' 'S' ' '
[Example 4] When setting the GAMMA MODE of the COLOR ENHANCER-USER to DETAIL. (Figures and symbols
enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
30 30 43 45 55 31 47 53 32 0D
'0' '0' 'C' 'E' 'U' '1' 'G' 'S' '2' '
ASCII
HP 48h 50h
VP 56h 50h
FN 46h 4Eh
TRK 54h 52h 4Bh
CIN 43h 49h 4Eh
VOS 56h 4Fh 53h
HLD 48h 4Ch 44h
HLB 48h 4Ch 42h
HLE 48h 4Ch 45h
CLP 43h 4Ch 50h
CLW 43h 4Ch 57h
VSC 56h 53h 43h
LPF 4Ch 50h 46h
SHU 53h 48h 55h
SHL 53h 48h 4Ch
SHLS 53h 48h 4Ch 53h
SHRS 53h 48h 52h 53h
'0' '1' '2' '3'
30h 31h 32h 33h
'
30 30 41 50 4F 4E 31 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
'
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
30 30 53 2B 31 30 0D
'0' '0' 'S' '+' '1' '0' '
'
30 30 43 45 55 31 47 53 32 0D
'0' '0' 'C' 'E' 'U' '1' 'G' 'S' '2' '
HEX
+ (increment), - (decrement)
+ (increment), - (decrement)
00–31
+ (increment), - (decrement)
0 (RGB), 1 (YC
00 (90%) – 10 (100%)
0 (OFF), 1 (ON)
00–99
00–99
001–255
01–63
0 (AUTO), 1 (OFF)
0 (OFF), 1 (ON)
00–20
00–20
00–20
00–20
'4' '5' '6' '7'
34h 35h 36h 37h
Status code
from the projector
'
Status code
from the projector
Status code
from the projector
'
Status code
from the projector
6
VALUE
*1
*1
*1
C /YP P ), 2 (AUTO)
B R B R
'8' '9'
38h 39h
Description
Command for setting the AUTO
POWER ON to ON
Command receipt confirmation
(Command echo back)
Description
Command for setting the picture
control
Command receipt confirmation
' (Command echo back)
Description
Command for checking the TINT
setting
Check result (+10)
Description
Command for setting the picture
control
Command receipt confirmation
' (Command echo back)