Mitsubishi Electric HC1600 Control Manual page 5

*1) Setting range differs depending on the input signals.
• Some commands are not executed depending on the input signal. The operational restrictions same as those
on the menu setting are applied. Refer to "Menu operation" in the User Manual for more details.
How to set the value
Use the ASCII or HEX code as shown below to set the value.
ASCII '+' '-'
HEX 2Bh 2Dh
[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are
ASCII codes.):
Sending commands
from the PC, etc.
30 30 41 50 4F 4E 31 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the
CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in
quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
30 30 53 0D
'0' '0' 'S' ' '
• To set TINT at 0, enter +00. (-00 is invalid.)
[Example 4] When setting the REFERENCE of GAMMA MODE-USER 1 to CINEMA (+2), HIGH to -2, MID to +3
and LOW to 0. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
30 30 47 53 55 31 2B 32 2D 30 32 2B 30 33 2B 30 30 OD
'0' '0' 'G' 'S' 'U' '1' '+' '2' '-' '0' '2' '+' '0' '3' '+' '0' '0' '
'0' '1' '2' '3'
30h 31h 32h 33h
'
30 30 41 50 4F 4E 31 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
'
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
30 30 53 2B 31 30 0D
'0' '0' 'S' '+' '1' '0' '
'
30 30 47 53 55 31 2B 32 2D 30 32 2B 30 33 2B 30 30 OD
'0' '0' 'G' 'S' 'U' '1' '+' '2' '-' '0' '2' '+' '0' '3' '+' '0' '0' '
'4' '5' '6' '7'
34h 35h 36h 37h
Status code
from the projector
'
Status code
from the projector
Status code
from the projector
'
Status code
from the projector
5
'8' '9'
38h 39h
Description
Command for setting the AUTO
POWER ON to ON
Command receipt confirmation
(Command echo back)
Description
Command for setting the picture
control
Command receipt confirmation
' (Command echo back)
Description
Command for checking the TINT
setting
Check result (+10)
Description
Command for setting of
GAMMA MODE-USER 1
Command receipt confirmation
' (Command echo back)