Table of Contents
Advertisement
A
Make connections
Connect the player's VIDEO OUT or S-VIDEO OUT and AUDIO
OUT connectors to your recorder's VIDEO or S-VIDEO and
AUDIO input connectors on the front panel.
B
Set the recorder's input mode
Press AUX (number key "0" and/or PR to select "F-1" for the
AUDIO and VIDEO input connectors or "S-1" for AUDIO and S-
VIDEO input connectors.
C
Load the end point
Load the recording cassette into your recorder, and play it back to
determine the edit-out point (the end of the segment to be
replaced) using the JOG dial, or pressing w e and 9.
D
Reset the counter
Press 0000.
● The counter is reset to "0:00:00".
E
Locate the start point
Determine the edit-in point (the biginning of the segment to be
replaced) using the JOG dial, or press w e and 9.
● Be sure to engage the Still mode at the edit-in point.
F
Engage the Insert Editing mode
Press INSERT.
● Your recorder enters the insert Pause mode. ("
displayed on the TV screen.)
● The TV screen changes from the still picture to the input source
you are going to record.
G
Start Editing
Load the source cassette and play back the segment that is to be
inserted. When you reach the start of the section of the source
tape that you wish to insert, press 4 to start the tape in your
recorder ; Insert Editing begins at this point.
● "
" is displayed on the TV screen.
H
End Insert Editing
At counter "0:00:00", Insert Editing will stop automatically while
the tape continues running in the Play mode. If you wish to stop
Insert Editing before the specified edit-out point, press 0000.
AV Insert Editing
If you want to replace the picture, Hi-Fi audio soundtrack and
normal audio soundtrack at the same time...
...In step 6, after you press INSERT, press A.DUB also. ("
" " are displayed on the TV screen.)
NOTES:
● All necessary cables can be obtained from your dealer.
● Insert Editing is not possible with cassettes whose record safety
tab has been removed.
● When Insert Editing is performed on a tape has been recorded
on another video recorder, the inserted portion may appear
distorted.
● In Insert Editing, the recording speed (SP/LP) is determined by
the previous recording to be replaced. If the previous
recording's speed changes within a single edit, the inserted
picture will be distorted at the switching point.
● A small portion of the recording which precedes an insert edit
may be erased.
● Insert Editing is also possible using the rear panel AV1 (L-1) IN/
OUT or AV2 (L-2) IN/DECODER connector. When using these
21-pin SCART connectors, be sure to select the correct input
mode ("L-1" or "L-2") in step 2.
● The soundtrack default setting is "HIFI" (
change the sound which you wish to hear. The soundtrack
selected during Insert Pause mode will be stored in the
recorder's memory and will be selected when you perform Insert
Editing the next time. The soundtrack will be reset back to
"HIFI" if the recorder's memory backup has expired.
Connecting/Using a Stereo System
These instructions enable you to connect your video recorder to
your Hi-Fi stereo system (if you have one) and listen to the
soundtrack through the stereo.
Speaker
" and " " are
Make Connections
Connect the AUDIO OUT L and R connectors on your video
recorder to the AUX IN or TAPE MONITOR terminals on your
stereo system's receiver or amplifier.
NOTES:
● When connecting your recorder's audio output connectors to a
● If stereo or bilingual TV broadcasts are receivable in your area,
" and
● When listening to sound through the connected stereo system,
CAUTIONS
● This recorder has a dynamic range of more than 80 dB with
● Some speakers and televisions are specially shielded to prevent
8). Press AUDIO to
— 22 —
System Connections
FM Tuner
CD Player
Stereo Amplifier
I
AUX IN or TAPE MONITOR
Television
Speaker
Mains
outlet
stereo amplifier, make sure you connect L and R correctly.
this recorder can record them independently of the TV set and
play them back through the connected stereo system.
turn the TV's volume down completely.
regards to its Hi-Fi audio capability. It is recommended that you
check the maximum level if you are going to listen to the Hi-Fi
audio signals through a stereo amplifier. A sudden surge in the
input level to the speakers may damage them.
television interference. If both are of the non-shielded type, do
not place the speakers adjacent to the TV set as this can
adversely affect the video playback pictur.
Audio Cable
(not provided)
(MONO)
Rear View
AUDIO OUT
Advertisement
Table of Contents
