Control List - Yamaha S80 Data List

Control List

Control Set Destination Parameter
No. LCD
00 off
01 Volume
02 RevSend
03 ChoSend
04 INS1-P1:EF1
: :
13 INS1P10:EF1
14 INS2-P1:EF2
: :
29 INS2P16:EF2
30 CLFOSpd
31 CLFO-D1
32 CLFO-D2
33 PorTime
34 ELM-Lvl
35 ELM-Pan
36 ELM-Dly
37 ELFOSpd
38 ELFO-PM
39 ELFO-AM
40 ELFO-FM
41 PCH-Crs
42 PCH-Fin
43 PEG-Dpt
44 PEG-Hld
45 PEG-Atk
46 PEG-D1
47 PEG-D2
48 PEG-Rel
49 AEG-Atk
50 AEG-D1
51 AEG-D2
52 AEG-Rel
53 FEG-Dpt
54 FEG-Hld
55 FEG-Atk
56 FEG-D1
57 FEG-D2
58 FEG-Rel
59 FLT-Frq
60 FLT-Rez
61 HPF-Frq
The destionation parameters 00 - 29 can be used for all Controller Sets.
However, in the case of the Plug-in voices, only the parameters 00 - 13 are
available.
The parameters 30 - 61 are available for the Normal voices except for the
Plug-in voices.
The parameters 04 - 29 are available only when Insertion effect is applied to
the voice, and the effective parameter type differs depending on the
currently selected effect type. If the destination parameter is effective, it's
actual parameter name will be displayed on the LCD. For example,
"INS1P10" of the number 13 will be replaced with the actual parameter
name. If not, the LCD displays the one like "INS1P10" shown in the above
list in the Controller Set function, and "-----" in the Play mode.
Downloaded from: http://www.usersmanualguide.com/
Parameter
:off
Voice Volume
Reverb Send
Chorus Send
Insertion Effect 1 Parameter 1
:
Insertion Effect 1 Parameter 10
Insertion Effect 2 Parameter 1
:
Insertion Effect 2 Parameter 16
Common LFO Speed
Common LFO Depth1
Common LFO Depth2
Common Portamento Time
Element Level
Element Pan
Element Key On Delay
Element LFO Speed
Element LFO Pitch Modulation Depth
Element LFO Amplitude Modulation Depth
Element LFO Filter Modulation Depth
Element Pitch Coarse
Element Pitch Fine
Element Pitch EG Depth
Element Pitch EG Hold Time
Element Pitch EG Attack Time
Element Pitch EG Decay1 Time
Element Pitch EG Decay2 Time
Element Pitch EG Release Time
Element Amplitude EG Attack Time
Element Amplitude EG Decay1 Time
Element Amplitude EG Decay2 Time
Element Amplitude EG Release Time
Element Filter EG Depth
Element Filter EG Hold Time
Element Filter EG Attack Time
Element Filter EG Decay1 Time
Element Filter EG Decay2 Time
Element Filter EG Release Time
Element Filter Cutoff Frequency
Element Filter Resonance
Element Filter HPF Cutoff Frequency
System Controller Destination Parameter
No. LCD
00 off off
01 EQLow-G MEQ Low Gain
02 EQLow-F MEQ Low Frequency
03 EQLow-Q MEQ Low Q
04 EQLoM-G MEQ Low Mid Gain
05 EQLoM-F MEQ Low Mid Frequency
06 EQLoM-Q MEQ Low Mid Q
07 EQMid-G MEQ Mid Gain
08 EQMid-F MEQ Mid Frequency
09 EQMid-Q MEQ Mid Q
10 EQHiM-G MEQ High Mid Gain
11 EQHiM-F MEQ High Mid Frequency
12 EQHiM-Q MEQ High Mid Q
13 EQHi-G MEQ High Gain
14 EQHi-F MEQ High Frequency
15 EQHi-Q MEQ High Q
16 REV-P1 ReverbParameter 1
: :
25 REV-P10 Reverb Parameter 10
26 REV-Rtn Reverb Return
27 REV-Pan Reverb Pan
28 CHO-P1 Chorus Parameter 1
: :
37 CHO-P10 Chorus Parameter 10
38 CHO-Rtn Chorus Return
39 CHO-Pan Chorus Pan
40 Cho>Rev Send Chorus To Reverb
41 ARP-Typ Arpeggio Type
42 ARP-Unt Arpeggio Unit Multiply
43 ARP-Vel Arpeggio Velocity Rate
44 ARP-Gat Arpeggio Gate Time Rate
45 Tempo Arpeggio/Sequencer Tempo
46 EG-Atck QED EG Attack Time
47 EG-Decy QED EG Decay Time
48 EG-SusL QED EG Sustain Level
49 EG-Rele QED EG Release Time
50 Cutoff QED Cutoff Frequency
51 Reso QED Resonance
As to the parameters 16 - 25 and 28 - 37, the effective parameter type
differs depending on the currently selected effect type. If the destination
parameter is effective, it's actual parameter name will be displayed on the
LCD. For example, "REV-P10" of the number 25 will be replaced with the
actual parameter name. If not, the LCD displays the one like "REV-P10"
shown in the above list in the Controller Set function, and "-----" in the Play
mode.
15
Parameter
:
: