Advertisement
Quick Links
Invexs 190 Readers
1.
General
The Invexs 190 reader series is capable of reading (simultaneously) Nedap,
Mifare and DESFire credentials due to its dual reader technology. The
Invexs 190 is designed to be used on door pillars (mullion) and suitable for
outside and inside use. A model with keypad is also available. The Invexs
output can be set to either Wiegand, XS RF modulation or RS485 protocol
(plain or encrypted). Functionality and output are determined by the
configuration of the Invexs reader. The configuration is defined using the
programm AEreco, and deployed by the configuration card or via AEmon.
(More information about configurations can be found in Convexs Invexs
Installation Manual). Three LEDs (red, green, blue) and beeper are included.
LEDs around the keypad ciphers light up only in case a PIN code is
requested. The pigtail cable can be lead directly backwards or when using
the additional spacer (art. nr . 9949887) to the top or bottom.
2.
Dimensions
3.
Mounting Procedure Invexs
For mounting the Invexs 190, the mounting plate must be placed on the wall
first. For removing the mounting plate from the Invexs 190, unscrew the
screw
01
(Torx, M5) at the bottom of the Invexs and push the Invexs 190
slightly up
. The plate can be mounted using the 4 holes. Place the cable to
02
the correct position and replace the Invexs 190.
Date: 21-03-2017 Version 8.0 Document no.: 5278210
This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no license under any patent or other right, nor does
the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be
reproduced in any way, in whole or in part, without the written consent of the publisher.
© Nedap N.V., P.O. Box 103, NL-7140 AC GROENLO, The Netherlands
Mifare Nedap dual technology mullion readers
4 x 5
12
32
30
50
Quick Install sheet
Dimensions: 191 x 50 x 30 mm.
4 mounting holes available at 32 x 155 mm
Cable pigtail: 10 x 0,14 mm shielded, 3m
Optional spacer (max thickness 10 mm) is
available for other cable outlet (top or
bottom)
10 x 0.14
Shield
1
2
02
Push up
1
01
Un screw
Mounting
plate
EN
EN
Advertisement
Related Manuals for Nedap Invexs 190 Series
Summary of Contents for Nedap Invexs 190 Series
- Page 1 Mifare Nedap dual technology mullion readers General The Invexs 190 reader series is capable of reading (simultaneously) Nedap, Mifare and DESFire credentials due to its dual reader technology. The Invexs 190 is designed to be used on door pillars (mullion) and suitable for outside and inside use.
- Page 2 Cable shield (wire 11) must be connected to the metal case of the external device • If connected to a 120kHz RF device (AEOS Nedap reader AEpack or XS device) the • power is supplied via the Convexs adapters (AX1014 for AEpacks, AB350 for XS devices).
- Page 3 Quick Install sheet | Invexs 190 Readers Mifare Nedap dual technology mullion readers Function of LEDs and Beeper is controlled by used application settings of Invexs. Green and Red LED can be controlled by hardware signals (wire 8 and 10) or RS485NR, Blue LED indirectly by UL and NA, if this setting is activated (configuration) or by wire 9.
- Page 4 Or 5 x 0,25mm² shielded, max cable length: 50 meter, cable capacity <= 100pF/meter Wiegand: 4 x 0,25mm² shielded (excl. LEDs), max cable length: 150 meter, depending on receiving device MORE INFORMATION: Contact your local Nedap supplier or check our website www.nedapsecurity.com Version 8.0...