SPECIFICATIONS HR MODEL K, EZ, HS MODELS • Design and specifications are subject to change without notice • Design and specifications are subject to change without notice ACCESSORIES/PACKAGE LIST REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION 1 8A-CLD-906-010 IB,EZ(9L)FM<EZS,EZL>...
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
ELECTRICAL MAIN PARTS LIST REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION C271 87-010-221-080 CAP, ELECT 470-10V C272 87-010-221-080 CAP, ELECT 470-10V 87-A21-064-010 IC,LA4227 C278 87-010-405-080 CAP, ELECT 10-50V 87-A21-443-040 C-IC,M62495AFP C279 87-010-385-080 CAP, ELECT 220-25V 87-A20-446-010 C-IC,LA9241ML C280...
Page 5
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION C764 87-012-337-080 C-CAP,U 56P-50 CH<HRS> J202 87-A60-659-010 TERMINAL,SPKR 4P HSP-134V-05Z C764 87-012-271-080 CAP, U 560P-50<KS,EZS,EZL> J203 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN C765 87-012-286-080 CAP, U 0.01-25 J801 87-A60-702-010 TERMINAL,ANT 4P CJ-9036<HRS>...
Page 6
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION C402 87-A11-132-080 CAP,TC U 0.01-50 K B C492 87-010-221-080 CAP, ELECT 470-10V C403 87-010-263-080 CAP, ELECT 100-10V C493 87-012-286-080 CAP, U 0.01-25 C404 87-010-248-080 CAP, ELECT 220-10V C494 87-A11-132-080 CAP,TC U 0.01-50 K B C405...
REF. NO PART NO. KANRI DESCRIPTION !PR901 87-A90-091-080 PROTECTOR,2A 491 87-A90-178-010 SW SL1-1-2<HRS> !SW901 !TM901 87-A60-317-010 TERMINAL, 1P MSC !TM902 87-A60-317-010 TERMINAL, 1P MSC MOTOR C.B 9X-262-576-910 MOTOR GEAR ASSY PIN3 91-564-722-110 CONNECTOR 6P 91-572-085-120 LEAF SW • Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.
Page 23
< TUNER SECTION > < TAPE SECTION > 1. AM/MW VT Adjustment <HR> 11. Tape speed Adjustment Test point: FFE801 (4PIN) Settings: • Test tape: TTA-100 Adjustment location: L981 (3/3) • Test point: J201 (PHONES jack) 7.5V±0.05V ............1710kHz • Adjustment location: SFR of deck motor 0.3V (CHECK) ............
Page 24
IC DESCRIPTION IC, LA9241ML Pin No. Pin Name Description Pin to which external pickup photo diode is connected. RF signal is created by adding with the FIN2 FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal. FIN1 Pin to which external pickup photo diode is connected.
Page 25
Pin No. Pin Name Description Pin from which TES signal is output to DSP. “High Frequency Level” is used to judge whether the main beam position is on top of bit or on top of mirror. SLOF Sled servo off control input pin. 39, 40 CV–, CV+ CLV error signal input pin from DSP.
Page 26
IC, LC78622ED Pin No. Pin Name Description DEFI Defect sense signal (DEF) input pin. (Connect to 0V when not used). Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Phase comparator output pin to control external VCO. VVSS —...
Page 27
Pin No. Pin Name Description RVSS — R-channel GND. Be sure to connect to 0V. RCHO R-channel output pin. R-channel 1-bit DAC. RVDD — R-channel power supply pin. MUTER R-channel mute output pin. (Not Connected) XVDD — Crystal oscillator power supply pin. XOUT Pin to which external 16.9344 MHz crystal oscillator is connected.
Page 28
IC, LC867132V-5S27 Pin No. Pin Name Description O-RMC/CE CD read/write control output and TU CE. O-DATA Data output to M62495FP. O-CLK Output CLK to tuner PLL. — — Not Connected. O-CLK SFT Clock shift output of the microcomputer. I-HOLD Hold status detection. I-RST Microcomputer reset.
Page 29
Pin No. Pin Name Description O-CD LED LED ON/OFF control output for CD functions. (Not connected) O-TU LED LED ON/OFF control output for TU functions. (Not connected) O-TA LED LED ON/OFF control output for TAPE functions. (Not Connected) O-ROCK LED LED ON/OFF control output for ROCK.
CD MECHANISM EXPLODED VIEW 1/1 SHAFT,SLIDE SF-P101NR CHASSIS SPINDLE MOTOR C,B MOTOR(M3) CD MECHANISM PARTS LIST 1/1 REF. NO PART NO. KANRI DESCRIPTION 1 S2-121-A28-400 COVER GEAR 2 S2-511-A21-000 GEAR MIDDLE 3 S2-511-A21-100 GEAR,DRIVE A S1-PN2-03R-OSE SCR PAN PCS 2-3 B 87-261-073-410 SCR S-TPG FLT 2.6-6 ALL M8-ZZK-E90-070...