Related Manuals for Samsung DW80B6060UG
Summary of Contents for Samsung DW80B6060UG
- Page 1 Dishwasher Installation manual DW80B70* Series, DW80B60* Series DW7000B_DW80B7070_AA_DD68-00242A-00_EN.indd 1 2021-11-09 4:41:03...
-
Page 2: Installation
Contents Safety instructions Important safety instructions Before using your dishwasher Installation Product dimensions Cabinet dimensions Specifications Scan the QR code* to view our helpful installation videos. * Requires reader to be installed on your smartphone. English DW7000B_DW80B7070_AA_DD68-00242A-00_EN.indd 2 2021-11-09 4:41:03... -
Page 3: Important Safety Instructions
It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher. Samsung is not liable for damages resulting from improper use. -
Page 4: California Proposition 65 Warning
Safety instructions California Proposition 65 Warning WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov Read all instructions before using the appliance. Install and store the dishwasher inside, away from exposure to weather. CAUTION • Do not install the dishwasher near electrical components. Keep the dishwasher away from open flames. -
Page 5: Before Using Your Dishwasher
Make sure to use a new water supply line. Old lines are susceptible to breakage because they become hardened and may cause property damage due to a water leakage. The dishwasher must be connected to a hot water supply with a temperature between 120 °F (49 °C) ~ 149 °F (65 °C). -
Page 6: Parts Required
Installation Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you are not at risk of injury when washing dishes. STEP 1 Check the parts and tools Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher. - Page 7 Not provided Power cable Twist on wire Strain relief Electrical tape & connector Standard duct tape Hot water supply 90° Fitting ( ") Tube fittings Air gap line Rubber connector NOTE For the hot water supply line – We strongly recommend using "...
- Page 8 Installation Tools required Electric drill Safety glasses Gloves Flashlight Adjustable wrench Wire stripper Pliers Nipper Tape measure Pencil Phillips screwdriver Flat screwdriver Tubing cutter Cutting knife Hole saw Level Torx t20 Hex L-wrench English DW7000B_DW80B7070_AA_DD68-00242A-00_EN.indd 8 2021-11-09 4:41:05...
- Page 9 NOTE New installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher.
- Page 10 Installation If this is a new installation, follow these steps: 1. Using a 2 inch hole saw, cut a hole into the side of the cabinet that holds the sink as shown in Figure 1-1 below. 2. If the base inside the sink cabinet is raised above the kitchen floor and is higher than the connections on the dishwasher, make a hole in the base inside the cabinet and in the cabinet side as shown in Figure 1-2.
-
Page 11: Product Dimensions
Product dimensions Front view DW80B7070**, DW80B6060** DW80B7071**, DW80B6061** " (605 mm) " (605 mm) Junction box Junction box Side view DW80B7070**, DW80B6060** DW80B7071**, DW80B6061** " (693 mm) " (60 mm) " (70 mm) " (520 mm) " (520 mm) You must arrange the 25"... -
Page 12: Cabinet Dimensions
Installation Cabinet dimensions NOTE This dishwasher is designed to be enclosed on the top and on both sides by a standard 24" (610 mm) minimum residential kitchen cabinet unit. The installation cabinet must be clean and free of any obstructions. 24"... -
Page 13: Step 3 Check Water Supply Requirements And Cautions
STEP 3 Check water supply requirements and cautions • The hot water supply line pressure must be between 20 ~ 120 psi (140 ~ 830 kPa). • Adjust the water heater to deliver water between 120 °F (49 °C) ~ 149 °F (65 °C). - The dishwasher must be connected to a hot water supply between 120 °F (49 °C) ~ 149 °F (65 °C). - Page 14 Installation STEP 4 Check the electrical requirements and cautions The electrical requirements for the dishwasher are as follows: • In the United States, install in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/ Provincial and Municipal codes and/or local codes.
-
Page 15: Step 5 Unpacking And Inspecting The Dishwasher
STEP 5 Unpacking and inspecting the dishwasher Unpack the dishwasher in an open area free of obstruction both around the packaging and overhead. We recommend that you retain all of the packing materials until the dishwasher is fully installed and operational to ensure you have removed all the product’s components from the packing materials prior to disposal. - Page 16 Installation Inspecting Mechanical 1. Check the plastic base assembly to ensure that it is intact 2. Check the dishwasher’s feet to ensure they are in place and can be adjusted so you can level and secure the dishwasher. 3. Check all the visible components on the bottom of the dishwasher to ensure they are intact and secure.
- Page 17 STEP 6 Mounting the custom panel 1. Open the door and fit the custom panel in the front bottom of the door. Make sure that the ribs of the panel fit into the corresponding holes (totaling 6) of the door. 2.
- Page 18 Installation 3. When both sides of the panel lock into place, press the top center of the custom panel to secure it to the top of the door. NOTE • Make sure that the custom panel fits in the dishwasher properly. •...
- Page 19 6. Insert the caps on either side. Make sure the rib of the cap fits in the hole of the dishwasher in the right direction. 7. This is the completion of mounting the custom panel. English 19 DW7000B_DW80B7070_AA_DD68-00242A-00_EN.indd 19 2021-11-09 4:41:06...
-
Page 20: Step 7 Preparing The Dishwasher
Installation STEP 7 Preparing the dishwasher 1. Attach the protective sticker (A). - To prevent damage, put the protective sticker on the bottom of the counter top as shown in the picture. NOTE • Before putting the protective sticker, clean the counter top as shown in the picture. •... - Page 21 3. Use the provided nut connector to connect the water hose to the dishwasher. Follow these steps: 01 Disconnect the 90° fitting (A) from the hose (B). 02 Remove the seal (C) and the nut (D) from the 90° fitting. 03 From the provided nut connector, separate the seal (E) and the nut (F), and then assemble them to the 90°...
- Page 22 Installation Figure 4 A’ A’ Junction box Strain relief 90° fitting CAUTION Do not overtighten the 90° Fitting. (Below 280 lb·in (31.6 N·m)) Doing so may damage the water inlet valve and cause a water leak. English DW7000B_DW80B7070_AA_DD68-00242A-00_EN.indd 22 2021-11-09 4:41:06...
- Page 23 STEP 8 Placing the dishwasher and connecting the hot water supply line 1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (See STEP 9, Leveling the Dishwasher.) 2.
- Page 24 Installation Figure 5 Side gasket Junction box Side gasket 1 inch Drain hose Hot Water Supply Line Power cable Inlet valve built-in hook Hot Water Supply Line Elbow ( " (9.5 mm)) CAUTION Do not overtighten the 90° Fitting. Doing so may damage the water inlet valve and cause a water leak. Make sure the dishwasher is positioned to the center.
-
Page 25: Step 9 Leveling The Dishwasher
STEP 9 Leveling the dishwasher 1. Open the door and place the level against the top of the tub on the inside and check if the the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level. - Page 26 Installation NOTE • If the leveling legs are rotated to the left (clockwise), they are loosened and the front of the dishwasher is raised. If they are rotated to the right (counter clockwise), they are tightened and the front of the dishwasher is lowered. •...
-
Page 27: Step 10 Securing The Dishwasher
STEP 10 Securing the dishwasher You must secure the dishwasher to the countertop or cabinet side walls for additional stability and safety. To the countertop If the countertop is made of wood or the material will not be damaged by drilling, follow this. - Page 28 Installation To the sides If the countertop is made of granite, marble, or any other material that can be damaged by drilling, follow this. 1. Put a large towel into the bottom of the dishwasher(covering the filter) to prevent wood shavings or a dropped screw from falling into the sump.
- Page 29 STEP 11 Securing 1. Check the parts on the sink to which the drain hose will be connected. 2. There are several ways to insert the drain hose into the drain hose connector of the sink, as shown in the following figures. You must connect the drain hose in accordance with the water pipe installation regulations in your region.
- Page 30 Installation Air gap Drain hose Hose clamp Hose clamp With disposal Disposal with an air gap Without an air gap Knock out plug in garbage disposal before connecting the drain hose. 3. Check the size of the sink’s drain hose connector. If needed, cut the drain hose so its end fits onto the sink connector ( in.
- Page 31 NOTE To prevent leaks or drainage problems, make sure the drain hose is not damaged, kinked, or twisted. 8. Do not cut the ribbed area of the drain hose to fit the size. When arranging the drain hose, take caution not to contact on sharp edges of the cabinet or under-sink. CAUTION •...
- Page 32 Installation Figure 9 1 in. (25 mm) (16 mm) (22 mm) If necessary, cut off the dotted line of the drain hose to fit the size. Figure 10 To prevent backflow for models without the air gap, secure the drain hose to the Sink side wall of the kitchen cabinet using cable ties or other fixtures.
-
Page 33: Step 12 Wiring Connections
STEP 12 Wiring connections 1. Before connecting the power cable to the dishwasher, make sure the circuit breaker is off. 2. In the junction box located at the front bottom right of the dishwasher, find the three power wires from the dishwasher including the grounding line. 3. - Page 34 Installation Figure 12 WARNING • Electrical Shock Hazard To avoid electrical shock, do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de-energized.
-
Page 35: Step 13 Completing The Installation
STEP 13 Completing the installation 1. Open the door and remove all foam, paper packaging, and unnecessary parts. 2. Turn on the circuit breaker you turned off before you began the installation. 3. Open the water supply valve to supply water to the dishwasher. 4. - Page 36 Installation 10. If the “LC” information code continues to appear on the window panel, contact a local service center. 11. Finally, attach the kick plate to the bottom of the dishwasher. While keeping the rubber skirt of the door taut, push the kick plate from the front of the rubber skirt inward underneath the door of the dishwasher.
-
Page 37: Specifications
Specifications Power supply 120 V, 15 A, 60 Hz AC Water pressure 20 ~ 120 psi (140 ~ 830 kPa) x 25 x 33 in. (605 x 636 x 860 mm) (DW80B7070AP / DW80B7070U*/ DW80B6060U*) Dimensions (Width × Depth × Height) x 26 x 33 in. - Page 38 Memo DW7000B_DW80B7070_AA_DD68-00242A-00_EN.indd 38 2021-11-09 4:41:08...
- Page 39 Memo DW7000B_DW80B7070_AA_DD68-00242A-00_EN.indd 39 2021-11-09 4:41:08...
- Page 40 DD68-00242A-00 DW7000B_DW80B7070_AA_DD68-00242A-00_EN.indd 40 2021-11-09 4:41:08...